參數資料
型號： MCZ33689DEW
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： System Basis Chip with LIN Transceiver
中文描述： 系統基礎芯片的LIN收發器
文件頁數： 19/31頁
文件大小： 309K
代理商： MCZ33689DEW
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33689
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
A System Basis Chip (SBC) is a monolithic IC combining
many functions found in standard microcontroller-based
systems; e.g., power management, communication interface,
system protection, and diagnostics.
The 33689 is a SPI-controlled SBC combining many
functions with a LIN transceiver for slave node applications.
The 33689 has a 5.0 V, 50 mA regulator with undervoltage
reset, output current limiting, overtemperature pre-warning,
and thermal shutdown. An externally selectable timing
Window Watchdog is also included.
The LIN transceiver has waveshaping that can be disabled
when high data rates are warranted. A single 50 mA and two
150 mA fully protected high-side switches with output
clamping are available for switching inductive or resistive
loads. The 150 mA switches are PWM capable.
Two high-voltage inputs can be used to monitor switches
or provide external wake-up. An internal current sense
operational amplifier is available for load current monitoring.
FUNCTIONAL PIN DESCRIPTION
LEVEL 1 AND LEVEL 2 INPUT PINS
(L1 AND L2)
These pins are used to sense external switches and to
wake up the 33689 from Sleep or Stop mode. During Normal
mode, the state of these pins can be read through the SPI
Register. (Refer to the section entitled
SPI Interface and
Register Description on page 24
for information on the SPI
Register.)
HIGH-SIDE DRIVER OUTPUT PINS 1 AND 2 (HS1
AND HS2)
These two high-side switches are able to drive loads such
as relays or lamps. They are protected against overcurrent
and overtemperature and include internal clamp circuitry for
inductive load protection. Switch control is done through
selecting the correct bit in the SPI Register. HS1 and HS2
can be PWM-ed if required through the IN input pin. The
internal circuitry that drives both high-side switches is an
AND function between the SPI bit HS1 (or HS2) and the IN
input pin.
If no PWM control is required, the IN pin must be
connected to the VDD pin.
HIGH-SIDE DRIVER OUTPUT PIN 3 (HS3)
This high-side switch can be used to drive small lamps,
Hall sensors, or switch pullup resistors. Control is done
through the SPI Register only.
No direct PWM control is possible on this pin.
This high-side switch features current limit to protect it
against overcurrent and short circuit conditions. It is also
protected against overtemperature.
VOLTAGE SUPPLY PINS 1 AND 2
(VS1 AND VS2)
The 33689 is supplied from a battery line or other supply
source through the VS1 and VS2 pins. An external diode is
required to protect against negative transients and reverse
battery. The 33689 can operate from 4.5 V and under the
jump start condition at 27 V DC. Device functionality is
guaranteed down to 4.5 V at VS1 and VS2 pins. These pins
sustain standard automotive voltage conditions such as load
dump at 40 V.
LIN BUS PIN (LIN)
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems and is based
on the LIN bus specification.
VOLTAGE SOURCE PIN (VDD)
The VDD pin is the 5.0 V supply pin for the MCU and the
current sense operational amplifier.
CURRENT SENSE OPERATIONAL AMPLIFIER
PINS (E+, E
-
, VCC, AND OUT)
These are the pins of the single-supply current sense
operational amplifier.
The E+ and the E- input pins are the non-inverting and
inverting inputs of the current sense operational amplifier,
respectively.
The OUT pin is the output pin of the current sense
operational amplifier.
The VCC pin is the + 5.0 V single-supply connection for the
current sense operational amplifier.
The current sense operational amplifier is enabled in
Normal mode only.
WATCHDOG CONFIGURATION PIN (
WDC
)
The
WDC
pin is the configuration pin for the internal
watchdog. A resistor is connected to this pin. The resistor
value defines the watchdog period. If the pin is left open, the
watchdog period is fixed to its default value (150 ms typical).
If no watchdog function is required, the
WDC
pin must be
connected to GND.
相關PDF資料
PDF描述
MCZ33742EG System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver
MCZ33790EG Two-Channel Distributed System Interface (DSI) Physical Interface Device
MCZ33793AEF Distributed System Interface (DSI) Sensor Interface
MCZ33797EK Four Channel Squib Driver IC
MCZ33800EK Engine Control Integrated Circuit
相關代理商/技術參數
參數描述
MCZ33689DEWR2 功能描述:輸入/輸出控制器接口集成電路 SBCLIN RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCZ33730EK 功能描述:線性穩壓器 - 標準 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
MCZ33730EK/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Switch Mode Power Supply with Multiple Linear Regulators
MCZ33730EKR2 功能描述:線性穩壓器 - 標準 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
MCZ33742EG 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*