- 您現在的位置：買賣IC網 > PDF目錄383595 > MCP73862 (Microchip Technology Inc.) Advanced Dual Cell, Fully Integrated Li-Ion /Li-Polymer Charge Management Controllers(增強型兩節高度集成的鋰離子/鋰聚合物充電管理控制器) PDF資料下載
參數資料
| 型號： | MCP73862 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Advanced Dual Cell, Fully Integrated Li-Ion /Li-Polymer Charge Management Controllers(增強型兩節高度集成的鋰離子/鋰聚合物充電管理控制器) |
| 中文描述： | 先進的雙電池，完全集成的鋰離子/鋰聚合物充電管理控制器（增強型兩節高度集成的鋰離子/鋰聚合物充電管理控制器） |
| 文件頁數： | 16/26頁 |
| 文件大小： | 402K |
| 代理商： | MCP73862 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
MCP73861/2
DS21893A-page 16
2004 Microchip Technology Inc.
5.1.6
BATTERY VOLTAGE SENSE (V
BAT3
)
The MCP7386X monitors the battery voltage at the
V
BAT3
pin. This input is tied directly to the positive
terminal of the battery pack.
5.1.7
BATTERY CHARGE CONTROL
OUTPUT (V
BAT1
, V
BAT2
)
The battery charge control output is the drain terminal
of an internal P-channel MOSFET. The MCP7386X
provides constant current, constant voltage regulation
to the battery pack by controlling this MOSFET in the
linear region. The battery charge control output should
be connected to the positive terminal of the battery
pack.
5.2
Digital Circuitry
5.2.1
CHARGE STATUS OUTPUTS
(STAT1,STAT2)
Two status outputs provide information on the state of
charge. The current-limited, open-drain outputs can be
used to illuminate external LEDs. Optionally, a pull-up
resistor can be used on the output for communication
with a host microcontroller. Table 5-1 summarizes the
state of the status outputs during a charge cycle.
The flashing rate (1 Hz) is based off a timer capacitor
(C
TIMER
) of 0.1 μF. The rate will vary based on the
value of the timer capacitor.
During a FAULT condition, the STAT1 status output will
be off and the STAT2 status output will be on. To
recover from a FAULT condition, the input voltage must
be removed and then reapplied, or the enable input
(EN) must be de-asserted to a logic-low, then asserted
to a logic-high.
When the voltage on the THERM input is outside the
preset window, the charge cycle will not start, or will be
suspended. The charge cycle is not terminated and
recovery is automatic. The charge cycle will resume or
start once the THERM input is valid and all other qual-
ification parameters are met. During an invalid THERM
condition, the STAT1 status output will be off and the
STAT2 status output will flash.
5.2.2
The V
SET
input selects the regulated output voltage of
the MCP7386X. With V
SET
tied to V
SS
, the MCP73861
and MCP73862 regulate to 4.1V and 8.2V, respec-
tively. With V
SET
tied to V
DD
, the MCP73861 and
MCP73862 regulate to 4.2V and 8.4V, respectively.
V
SET
INPUT
5.2.3
LOGIC ENABLE (EN)
The logic enable input pin (EN) can be used to
terminate a charge at any time during the charge cycle,
as well as to initiate a charge cycle or initiate a recharge
cycle.
Applying a logic-high input signal to the EN pin, or tying
it to the input source, enables the device. Applying a
logic-low input signal disables the device and termi-
nates a charge cycle. When disabled, the device’s
supply current is reduced to 0.17 μA, typically.
TABLE 5-1:
STATUS OUTPUTS
CHARGE
CYCLE STAT1
STAT1
STAT2
Qualification
Preconditioning
Constant
Current Fast
Charge
Constant
Voltage
Charge
Complete
Fault
THERM Invalid
Off
On
On
Off
Off
Off
On
Off
Flashing (1Hz,
50% duty cycle)
Off
Off
Off
On
Flashing (1Hz,
50% duty cycle)
Off
Disabled - Sleep
mode
Input Voltage
Disconnected
Note:
Off state: open-drain is high-impedance;
On state: open-drain can sink current,
typically 7 mA;
Flashing: toggles between off state and
on state.
Off
Off
Off
相關PDF資料 |
PDF描述 |
|---|---|
| MCP810 | Microcontroller Supervisory Circuit with Push-Pull Output(帶推挽輸出的微控制器監控電路) |
| MCP809 | Microcontroller Supervisory Circuit with Push-Pull Output(帶推挽輸出的微控制器監控電路) |
| MCR006YZPF | Thick film rectangular |
| MCR006YZPJ | Thick film rectangular |
| MCR006 | Thick film rectangular |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP73862-I/ML | 功能描述:電池管理 Daul High Integrated RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MCP73862-I/MLG | 功能描述:電池管理 Daul High Integrated Lead Free Package RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MCP73862-I/SL | 功能描述:電池管理 Charge mgmt contr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MCP73862T | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Advanced Single or Dual Cell, Fully Integrated Li-Ion/Li-Polymer Charge Management |
| MCP73862T-I/ML | 功能描述:電池管理 Daul High Integrated RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。