參數資料
型號： MCP73828
廠商： Microchip Technology Inc.
英文描述： Single Cell Lithium-Ion Charge Management Controller with Charge Complete Indicator and Temperature Monitor
中文描述： 單節鋰離子電池充電管理控制器，充電完畢指示燈和溫度監測器
文件頁數： 12/24頁
文件大?。?/td> 499K
代理商： MCP73828
MCP73828
DS21706A-page 12
2002 Microchip Technology Inc.
6.1
Application Circuit Design
Due to the low efficiency of linear charging, the most
important factors are thermal design and cost, which
are a direct function of the input voltage, output current
and thermal impedance between the external P-chan-
nel pass transistor, Q1, and the ambient cooling air.
The worst-case situation is when the output is shorted.
In this situation, the P-channel pass transistor has to
dissipate the maximum power. A trade-off must be
made between the charge current, cost and thermal
requirements of the charger.
6.1.1
COMPONENT SELECTION
Selection of the external components in Figure 6-1 is
crucial to the integrity and reliability of the charging sys-
tem. The following discussion is intended as a guide for
the component selection process.
6.1.1.1
SENSE RESISTOR
The preferred fast charge current for Lithium-Ion cells
is at the 1C rate with an absolute maximum current at
the 2C rate. For example, a 500 mAH battery pack has
a preferred fast charge current of 500 mA. Charging at
this rate provides the shortest charge cycle times with-
out degradation to the battery pack performance or life.
The current sense resistor, R
SENSE
, is calculated by:
Where:
V
CS
is the current limit threshold voltage
I
OUT
is the desired fast charge current
For the 500 mAH battery pack example, a standard
value 100 m
, 1% resistor provides a typical peak fast
charge current of 530 mA and a maximum peak fast
charge current of 758 mA. Worst case power dissipa-
tion in the sense resistor is:
A Panasonic ERJ-L1WKF100U 100 m
, 1%, 1 W
resistor is more than sufficient for this application.
A larger value sense resistor will decrease the peak
fast charge current and power dissipation in both the
sense resistor and external pass transistor, but will
increase charge cycle times. Design trade-offs must be
considered to minimize space while maintaining the
desired performance.
6.1.1.2
EXTERNAL PASS TRANSISTOR
The external P-channel MOSFET is determined by the
gate to source threshold voltage, input voltage, output
voltage, and peak fast charge current. The selected P-
channel MOSFET must satisfy the thermal and electri-
cal design requirements.
Thermal Considerations
The worst case power dissipation in the external pass
transistor occurs when the input voltage is at the maxi-
mum and the output is shorted. In this case, the power
dissipation is:
Where:
V
INMAX
is the maximum input voltage
I
OUT
is the maximum peak fast charge current
K is the foldback current scale factor
Power dissipation with a 5V, +/-10% input voltage
source, 100 m
, 1% sense resistor, and a scale factor
of 0.43 is:
Utilizing a Fairchild NDS8434 or an International Recti-
fier IRF7404 mounted on a 1in
2
pad of 2 oz. copper, the
junction temperature rise is 90°C, approximately. This
would allow for a maximum operating ambient temper-
ature of 60°C.
By increasing the size of the copper pad, a higher
ambient temperature can be realized or a lower value
sense resistor could be utilized.
Alternatively, different package options can be utilized
for more or less power dissipation. Again, design trade-
offs should be considered to minimize size while main-
taining the desired performance.
Electrical Considerations
The gate to source threshold voltage and R
DSON
of the
external P-channel MOSFET must be considered in the
design phase.
The worst case, V
GS
provided by the controller occurs
when the input voltage is at the minimum and the
charge current is at the maximum. The worst case, V
GS
is:
Where:
V
DRVMAX
is the maximum sink voltage at the V
DRV
output
R
SENSE
V
I
OUT
-----------
=
PowerDissipation
100m
758mA
2
×
57.5mW
=
=
PowerDissipation
V
INMAX
I
OUT
K
×
×
=
PowerDissipation
5.5V
758mA
×
0.43
×
1.8W
=
=
V
GS
V
DRVMAX
V
INMIN
I
OUT
R
SENSE
×
)
–
(
–
=
相關PDF資料
PDF描述
MCP9700 Low-Power Voltage Output Temperature Sensor
MCP9701 Low-Power Voltage Output Temperature Sensor
MCR100 Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管)
MCR12DSM Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管)
MCR12DSN Sensitive Gate Silicon Controlled Rectifiers(可控硅整流管)
相關代理商/技術參數
參數描述
MCP73828-4.1VUA 功能描述:電池管理 W/ Charge Comp Mon RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP73828-4.1VUATR 功能描述:電池管理 W/ Charge Comp Mon RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP73828-4.2VUA 功能描述:電池管理 W/ Charge Comp Mon RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP73828-4.2VUATR 功能描述:電池管理 W/ Charge Comp Mon RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP7382XEV 功能描述:電源管理IC開發工具 MCP7382X Li-Ion Batt Charger RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*