參數資料
型號： MCP6S21
廠商： Microchip Technology Inc.
英文描述： Single-Ended, Rail-to-Rail I/O, Low Gain PGA
中文描述： 單端，軌至軌I / O，低增益美國PGA
文件頁數： 17/43頁
文件大?。?/td> 880K
代理商： MCP6S21
2003 Microchip Technology Inc.
DS21117A-page 17
MCP6S21/2/6/8
4.2.2
RAIL-TO-RAIL INPUT
The input stage of the internal op amp uses two differ-
ential input stages in parallel; one operates at low V
IN
(input voltage), while the other operates at high V
IN
.
With this topology, the internal inputs can operate to
0.3V past either supply rail. The input offset voltage is
measured at both V
IN
= V
SS
- 0.3V and V
DD
+ 0.3V to
ensure proper operation.
The transition between the two input stages occurs
when V
IN
≈
V
DD
- 1.5V. For the best distortion and gain
linearity, avoid this region of operation.
4.2.3
RAIL-TO-RAIL OUTPUT
The Maximum Output Voltage Swing is the maximum
swing possible under a particular output load. Accord-
ing to the specification table, the output can reach
within 60 mV of either supply rail when R
L
= 10 k
and
V
REF
= V
DD
/2. See Figure 2-21 for typical performance
under other conditions.
4.2.4
INPUT VOLTAGE AND PHASE
REVERSAL
The amplifier family is designed with CMOS input
devices. It is designed to not exhibit phase inversion
when the input pins exceed the supply voltages.
Figure 2-34 shows an input voltage exceeding both
supplies with no resulting phase inversion.
The maximum voltage that can be applied to the input
pins (CHX) is V
SS
- 0.3V to V
DD
+ 0.3V. Voltages on the
inputs that exceed this absolute maximum rating can
cause excessive current to flow in or out of the input
pins. Current beyond ±2 mA can cause possible reli-
ability problems. Applications that exceed this rating
must be externally limited with an input resistor, as
shown in Figure 4-2.
FIGURE 4-2:
into an input pin.
R
IN
limits the current flow
4.3
Resistor Ladder
The resistor ladder shown in Figure 4-1 (R
LAD
= R
F
+
R
G
) sets the gain. Placing the gain switches in series
with the inverting input reduces the parasitic capaci-
tance, distortion and gain mismatch.
R
LAD
is an additional load on the output of the PGA and
causes additional current draw from the supplies.
In Shutdown mode, R
LAD
is still attached to the OUT
and V
REF
pins. Thus, these pins and the internal ampli-
fier’s inverting input are all connected through R
LAD
and the output is not high-Z (unlike the external op
amp).
While R
LAD
contributes to the output noise, its effect is
small. Refer to Figure 2-12.
4.4
Shutdown Mode
These PGAs use a software shutdown command.
When the SPI interface sends a shutdown command,
the internal op amp is shut down and its output placed
in a high-Z state.
The resistive ladder is always connected between
V
REF
and V
OUT
; even in shutdown. This means that the
output resistance will be on the order of 5 k
and there
will be a path for output signals to appear at the input.
The Power-on Reset (POR) circuitry will temporarily
place the part in shutdown when activated. See
Section 5.4, “Power-On Reset”, for details.
R
IN
V
---------–
Minimum expected V
2 mA
)
≥
R
IN
Maximum expected V
------------------------------------------------------------------------------
(
)
V
–
2 mA
≥
V
IN
R
IN
V
OUT
MCP6S2X
CHX
相關PDF資料
PDF描述
MCP6S22 Single-Ended, Rail-to-Rail I/O, Low Gain PGA
MCP6S28 400000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
MCP73827 Single Cell Lithium-Ion Charge Management Controller with Mode Indicator and Charge Current Monitor(單室鋰粒子充電器)
MCP73828(中文) Single Cell Lithium-Ion Charge Management Controller with Charge Complete Indicator and Temperature Monitor(單室鋰粒子充電器)
MCP73831 Miniature Single-Cell, Fully Integrated Li-Ion, Li-Polymer Charge Management Controllers
相關代理商/技術參數
參數描述
MCP6S21-I/MS 功能描述:特殊用途放大器 1-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
MCP6S21-I/P 功能描述:特殊用途放大器 1-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
MCP6S21-I/P 制造商:Microchip Technology Inc 功能描述:AMP PROGRAMMABLE GAIN 1 CH 6S21
MCP6S21-I/SN 功能描述:特殊用途放大器 1-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
MCP6S21-I/SN 制造商:Microchip Technology Inc 功能描述:Operational Amplifier (Op-Amp) IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*