- 您現在的位置：買賣IC網 > PDF目錄17108 > MCP4725EV (Microchip Technology)BOARD EVAL FOR MCP4725 PDF資料下載
參數資料
| 型號： | MCP4725EV |
| 廠商： | Microchip Technology |
| 文件頁數： | 16/50頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MCP4725 |
| 標準包裝： | 1 |
| DAC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 100k ~ 3.4M |
| 數據接口： | I²C |
| 設置時間： | 6µs |
| DAC 型： | 電壓 |
| 工作溫度： | -40°C ~ 125°C |
| 已供物品： | 2 板，CD |
| 已用 IC / 零件： | MCP4725 |
| 產品目錄頁面： | 673 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
2009 Microchip Technology Inc.
DS22039D-page 23
MCP4725
6.0
THEORY OF OPERATION
When the device is connected to the I2C bus line, the
device is working as a slave device. The Master (MCU)
can write/read the DAC input register or EEPROM
using the I2C interface command. The MCP4725
device address contains four fixed bits ( 1100 = device
code) and three address bits (A2, A1, A0). The A2 and
A1 bits are hard-wired during manufacturing, and A0 bit
is determined by the logic state of A0 pin. The A0 pin
can be connected to VDD or VSS, or actively driven by
digital logic levels.
The following sections describe the communication
protocol to send or read the data code and write/read
6.1
Write Commands
The write commands are used to load the configuration
bits and DAC input code to the DAC register, or to write
to the EEPROM of the device. The write command
types are defined by using three write command type
bits (C2, C1, C0). Table 6-2 shows the write command
types and their functions. There are three command
types for the MCP4725. The four “reserved” commands
in Table 6-2 are for future use. The MCP4725 ignores
the “reserved” commands. Write command protocol
examples are shown in Figure 6-1 and Figure 6-2.
The input data code is coded as shown in Table 6-1.
The MSB of the data is always transmitted first and the
format is unipolar binary.
TABLE 6-1:
INPUT DATA CODING
6.1.1
WRITE COMMAND FOR FAST
MODE (C2 = 0, C1 = 0, C0 = X,
X = DON’T CARE)
The fast write command is used to update the DAC
register. The data in the EEPROM of the device is not
affected by this command. This command updates
Power-Down mode selection bits (PD1 and PD0) and
12 bits of the DAC input code in the DAC register.
Figure 6-1 shows an example of the fast write
command for the MCP4725 device.
6.1.2
WRITE COMMAND FOR DAC INPUT
REGISTER (C2 = 0, C1 = 1, C0 = 0)
In MCP4725, this command performs the same
function as the Fast Mode command in Section 6.1.1
C0 = X, X = Don’t Care)”. Figure 6-2 shows the write
command protocol for the MCP4725.
As shown in Figure 6-2, the D11 - D0 bits in the third
and fourth bytes are DAC input data. The last 4 bits (X,
X, X, X) in the fourth byte are don’t care bits.
The device executes the Master’s write command after
receiving the last byte (4th byte). The Master can send
a STOP bit to terminate the current sequence, or send
a Repeated START bit followed by an address byte. If
the device receives three data bytes continuously after
the 4th byte, it updates from the 2nd to the 4th data
bytes with the last three input data bytes.
The contents of the register are updated at the end of
the 4th byte. The device ignores any partially received
data bytes if the I2C communication with the Master
ends before completing the 4th byte.
6.1.3
WRITE COMMAND FOR DAC INPUT
REGISTER AND EEPROM
(C2 = 0, C1 = 1, C0 = 1)
When the device receives this command, it (a) loads
the configuration and data bits to the DAC register, and
(b) also writes the EEPROM. When the device is
writing the EEPROM, the RDY/BSY bit goes low and
stays low until the EEPROM write operation is
completed. The state of the RDY/BSY bit can be
monitored by a read command. Figure 6-2 shows the
details of the this write command protocol and
Figure 6-3 shows the details of the read command.
Input Code
Nominal Output Voltage
(V)
111111111111
(FFFh)
VDD - 1 LSB
111111111110
(FFEh) VDD - 2 LSB
000000000010
(002h)
2 LSB
000000000001
(001h)
1 LSB
000000000000
(000h)
0
相關PDF資料 |
PDF描述 |
|---|---|
| MCP4728EV | BOARD EVAL 12BIT 4CH DAC MCP4728 |
| EMM08DRXI | CONN EDGECARD 16POS DIP .156 SLD |
| 9337110001 | HEAT SHRINK SLEEVE |
| 8420630001 | HEAT SHRINK SLEEVE |
| REF192GSZ-REEL | IC VREF SERIES PREC 2.5V 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP4725T-E/CH | 功能描述:數模轉換器- DAC SNGL 12B NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MCP4726A0T-E/CH | 功能描述:數模轉換器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MCP4726A0T-E/MAY | 功能描述:數模轉換器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MCP4726A1T-E/CH | 功能描述:數模轉換器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MCP4726A1T-E/MAY | 功能描述:數模轉換器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。