- 您現在的位置：買賣IC網 > PDF目錄17041 > MCP3424EV (Microchip Technology)EVALUATION BOARD FOR MCP3424 PDF資料下載
參數資料
| 型號： | MCP3424EV |
| 廠商： | Microchip Technology |
| 文件頁數： | 9/58頁 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR MCP3424 |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 18 |
| 采樣率（每秒）： | 3.75 ~ 240 |
| 數據接口： | I²C |
| 輸入范圍： | ±2.048 V |
| 在以下條件下的電源（標準）： | 135µA @ 240sps |
| 工作溫度： | -55°C ~ 125°C |
| 已用 IC / 零件： | MCP3424 |
| 已供物品： | 板 |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
| 相關產品： | MCP3424T-E/STTR-ND - IC ADC 18BIT 3.75SPS 4CH 14TSSOP MCP3424T-E/SLTR-ND - IC ADC 18BIT 3.75SPS 4CH 14-SOIC MCP3424-E/ST-ND - IC ADC 18BIT 3.75SPS 4CH 14TSSOP MCP3424-E/SL-ND - IC ADC 18BIT 3.75SPS 4CH 14-SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2009 Microchip Technology Inc.
DS22088C-page 17
MCP3422/3/4
5.0
USING THE DEVICES
5.1
Operating Modes
The user operates the device by setting up the device
configuration
register
using
a
write
command
(see Figure 5-3) and reads the conversion data using a
read command (see Figure 5-4 and Figure 5-5).
The device operates in two modes: (a) Continuous
Conversion Mode or (b) One-Shot Conversion Mode
(single conversion). This mode selection is made by
setting the O/C bit in the Configuration Register. Refer
to Section 5.2 “Configuration Register” for more
information.
5.1.1
CONTINUOUS CONVERSION
MODE (O/C BIT = 1)
The device performs a Continuous Conversion if the O/
C bit is set to logic “high”. Once the conversion is
completed, RDY bit is toggled to ‘0’ and the result is
placed at the output data register. The device
immediately begins another conversion and overwrites
the output data register with the most recent result. The
device clears the data ready flag (RDY bit = 0) when
the conversion is completed. The device sets the ready
flag bit (RDY bit = 1), if the latest conversion result has
been read by the Master.
When writing configuration register:
- Setting RDY bit in continuous mode does not
affect anything
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion
result is ready
5.1.2
ONE-SHOT CONVERSION MODE
(O/C BIT = 0)
Once the One-Shot Conversion Mode (single conver-
sion) is selected, the device performs only one
conversion, updates the output data register, clears the
data ready flag (RDY = 0), and then enters a low power
standby mode. A new One-Shot Conversion is started
again when the device receives a new write command
with RDY = 1.
When writing configuration register:
- The RDY bit needs to be set to begin a new
conversion in one-shot mode
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion is
done
This
One-Shot
Conversion
Mode
is
highly
recommended for low power operating applications
where the conversion result is needed by request on
demand. During the low current standby mode, the
device consumes less than 1 A maximum (or 300 nA
typical). For example, if the user collects 18 bit
conversion
data
once
a
second
in
One-Shot
Conversion mode, the device draws only about one
fourth of its total operating current. In this example, the
device consumes approximately 36 A (135 A /
3.75 SPS = 36 A), if the device performs only one
conversion per second (1 SPS) in 18-bit conversion
mode with 3V power supply.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7946SDZ | BOARD EVAL FOR AD7946 |
| EEC22DREH-S93 | CONN EDGECARD 44POS .100 EYELET |
| GMC08DRTF-S13 | CONN EDGECARD 16POS .100 EXTEND |
| MCP3421EV | BOARD EVAL FOR MCP3421 SOT23-6 |
| GEC44DRES-S13 | CONN EDGECARD 88POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3424T-E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3424T-E/MF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3424T-E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3424T-E/SL | 功能描述:模數轉換器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3424T-E/SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
發布緊急采購，3分鐘左右您將得到回復。