- 您現在的位置：買賣IC網 > PDF目錄385574 > MCP3304 (Microchip Technology Inc.) 13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface PDF資料下載
參數資料
| 型號： | MCP3304 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface |
| 中文描述： | 13位差分輸入，低功耗的A / D轉換器具有SPI串行接口 |
| 文件頁數： | 23/40頁 |
| 文件大?。?/td> | 666K |
| 代理商： | MCP3304 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
2002 Microchip Technology Inc.
DS21697B-page 23
MCP3302/04
7.2
Communicating with the MCP3302
and MCP3304
Communication with the MCP3302/04 devices is done
using a standard SPI-compatible serial interface. Initi-
ating communication with either device is done by
bringing the CS line low (see Figure 7-2). If the device
was powered up with the CS pin low, it must be brought
high and back low to initiate communication. The first
clock received with CS low and D
IN
high will constitute
a start bit. The SGL/DIFF bit follows the start bit and will
determine if the conversion will be done using single
ended or differential input mode. Each channel in
single ended mode will operate as a 12-bit converter
with a unipolar output. No negative codes will be output
in single ended mode. The next three bits (D0, D1 and
D2) are used to select the input channel configuration.
Table 7-2 and Table 7-3 show the configuration bits for
the MCP3302 and MCP3304, respectively. The device
will begin to sample the analog input on the fourth rising
edge of the clock after the start bit has been received.
The sample period will end on the falling edge of the
fifth clock following the start bit.
After the D0 bit is input, one more clock is required to
complete the sample and hold period (D
IN
is a “don’t
care” for this clock). On the falling edge of the next
clock, the device will output a low null bit. The next 13
clocks will output the result of the conversion with the
sign bit first, followed by the 12 remaining data bits, as
shown in Figure 7-2. Note that if the device is operating
in the single ended mode, the sign bit will always be
transmitted as a ‘
0
’. Data is always output from the
device on the falling edge of the clock. If all 13 data bits
have been transmitted, and the device continues to
receive clocks while the CS is held low, the device will
output the conversion result, LSB, first, as shown in
Figure 7-3. If more clocks are provided to the device
while CS is still low (after the LSB first data has been
transmitted), the device will clock out zeros indefinitely.
If necessary, it is possible to bring CS low and clock in
leading zeros on the D
IN
line before the start bit. This is
often done when dealing with microcontroller-based
SPI ports that must send 8 bits at a time. Refer to
Section 7.3 for more details on using the MCP3302/04
devices with hardware SPI ports
TABLE 7-2:
CONFIGURATION BITS FOR
THE MCP3302
TABLE 7-3:
CONFIGURATION BITS FOR
THE MCP3304
Control Bit
Selections
Input
Configuration
Channel
Selection
Single
/Diff
D2*
D1
D0
1
1
1
1
0
X
X
X
X
X
0
0
1
1
0
0
1
0
1
0
single ended
single ended
single ended
single ended
differential
CH0
CH1
CH2
CH3
CH0 = IN+
CH1 = IN-
CH0 = IN-
CH1 = IN+
CH2 = IN+
CH3 = IN-
CH2 = IN-
CH3 = IN+
0
X
0
1
differential
0
X
1
0
differential
0
X
1
1
differential
*D2 is don’t care for MCP3302
Control Bit
Selections
Input
Configuration
Channel
Selection
SinglE
/Diff
D2
D1
D0
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
single ended
single ended
single ended
single ended
single ended
single ended
single ended
single ended
differential
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH0 = IN+
CH1 = IN-
CH0 = IN-
CH1 = IN+
CH2 = IN+
CH3 = IN-
CH2 = IN-
CH3 = IN+
CH4 = IN+
CH5 = IN-
CH4 = IN-
CH5 = IN+
CH6 = IN+
CH7 = IN-
CH6 = IN-
CH7 = IN+
0
0
0
1
differential
0
0
1
0
differential
0
0
1
1
differential
0
1
0
0
differential
0
1
0
1
differential
0
1
1
0
differential
0
1
1
1
differential
相關PDF資料 |
PDF描述 |
|---|---|
| MCP6044 | 600 nA, Rail-to-Rail Input/Output Op Amps |
| MCP6041 | 600 nA, Rail-to-Rail Input/Output Op Amps |
| MCP6041T | 600 nA, Rail-to-Rail Input/Output Op Amps |
| MCP6042 | 600 nA, Rail-to-Rail Input/Output Op Amps |
| MCP6042T | 600 nA, Rail-to-Rail Input/Output Op Amps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3304-BI/P | 功能描述:模數轉換器 - ADC 13-bit Diff In 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3304-BI/SL | 功能描述:模數轉換器 - ADC 13-bit Diff In 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3304-BI/ST | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface |
| MCP3304-CI/P | 功能描述:模數轉換器 - ADC 13-bit Diff In 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3304-CI/SL | 功能描述:模數轉換器 - ADC 13-bit Diff In 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。