- 您現在的位置：買賣IC網 > PDF目錄385574 > MCP1701 (Microchip Technology Inc.) 2uA Low Dropoout Positive Voltage Refulator PDF資料下載
參數資料
| 型號： | MCP1701 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2uA Low Dropoout Positive Voltage Refulator |
| 中文描述： | 五成低Dropoout正電壓Refulator |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 385K |
| 代理商： | MCP1701 |
2004 Microchip Technology Inc.
DS21874A-page 9
MCP1701
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Ground Terminal (GND)
Regulator ground. Tie GND to the negative side of both
the output and the input capacitor. Only the LDO bias
current (2 μA, typical) flows out of this pin, as there is
no high current. The LDO output regulation is refer-
enced to this pin. Minimize voltage drops between this
pin and the negative side of the load.
3.2
Regulated Voltage Output (V
OUT
)
Connect V
OUT
to the positive side of the load and the
positive terminal of the output capacitor. The positive
side of the output capacitor should be located as close
as possible to the LDO V
OUT
pin. The current flowing
out of this pin is equal to the DC load current.
3.3
Unregulated Supply Input (V
IN
)
Connect the input supply voltage and the positive side
of the input capacitor to V
IN
. Like all low dropout linear
regulators, low source impedance is necessary for the
stable operation of the LDO. The amount of capacitance
required to ensure low source impedance will depend
on the proximity of the input source capacitors or battery
type. The input capacitor should be located as close as
possible to the V
IN
pin. For most applications, 1 μF of
capacitance will ensure stable operation of the LDO
circuit. For applications that have load currents below
100 mA, the input capacitance requirement can be
lowered. The type of capacitor used can be ceramic,
tantalum or aluminum-electrolytic. The low ESR charac-
teristics of the ceramic will yield better noise and PSRR
performance at high frequencies. The current flow into
this pin is equal to the DC load current, plus the LDO
bias current (2 μA, typical).
Pin No.
SOT-23A
Pin No.
SOT-89
Pin No.
TO-92
Name
Function
1
2
3
1
3
2
1
3
2
GND
V
OUT
V
IN
Ground terminal
Regulated voltage output
Unregulated supply input
相關PDF資料 |
PDF描述 |
|---|---|
| MCP23008 | 8-Bit I/O Expander with Serial Interface |
| MCP23S08 | 8-Bit I/O Expander with Serial Interface |
| MCP2551 | High-Speed CAN Transceiver |
| MCP3001 | 2.7V 10 BIT A/D CONVERTER WITH SPI SERIAL INTERFACE |
| MCP3002 | MCP300X 10-Bit Analog-to-Digital Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1701-1802I/TO | 功能描述:低壓差穩壓器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1701-2502I/TO | 功能描述:低壓差穩壓器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1701-3002I/TO | 功能描述:低壓差穩壓器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1701-3302I/TO | 功能描述:低壓差穩壓器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1701-5002I/TO | 功能描述:低壓差穩壓器 - LDO 250mA Adj LDO 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。