參數資料
型號: MC80C32-36SC
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 36 MHz, MICROCONTROLLER, CDIP40
封裝: 0.600 INCH, SIDE BRAZED, DIP-40
文件頁數: 71/132頁
文件大?。?/td> 10886K
代理商: MC80C32-36SC
276
8151H–AVR–02/11
ATmega128A
24.15 Boundary-scan Description Language Files
Boundary-scan Description Language (BSDL) files describe Boundary-scan capable devices in
a standard format used by automated test-generation software. The order and function of bits in
the Boundary-scan Data Register are included in this description.
24.16 Register Description
24.16.1
OCDR - On-chip Debug Register
The OCDR Register provides a communication channel from the running program in the micro-
controller to the debugger. The CPU can transfer a byte to the debugger by writing to this
location. At the same time, an internal flag; I/O Debug Register Dirty – IDRD – is set to indicate
to the debugger that the register has been written. When the CPU reads the OCDR Register the
7 LSB will be from the OCDR Register, while the MSB is the IDRD bit. The debugger clears the
IDRD bit when it has read the information.
In some AVR devices, this register is shared with a standard I/O location. In this case, the OCDR
Register can only be accessed if the OCDEN fuse is programmed, and the debugger enables
access to the OCDR Register. In all other cases, the standard I/O location is accessed.
Refer to the debugger documentation for further information on how to use this register.
24.16.2
MCUCSR - MCU Control and Status Register
The MCU Control and Status Register contains control bits for general MCU functions, and pro-
vides information on which reset source caused an MCU Reset.
Bit 7 – JTD: JTAG Interface Disable
When this bit is zero, the JTAG interface is enabled if the JTAGEN fuse is programmed. If this bit
is one, the JTAG interface is disabled. In order to avoid unintentional disabling or enabling of the
JTAG interface, a timed sequence must be followed when changing this bit: The application soft-
ware must write this bit to the desired value twice within four cycles to change its value.
If the JTAG interface is left unconnected to other JTAG circuitry, the JTD bit should be set to
one. The reason for this is to avoid static current at the TDO pin in the JTAG interface.
Bit 4 – JTRF: JTAG Reset Flag
This bit is set if a Reset is being caused by a logic one in the JTAG Reset Register selected by
the JTAG instruction AVR_RESET. This bit is reset by a Power-on Reset, or by writing a logic
zero to the flag.
Bit
7
6
5
4321
0
MSB/IDRD
LSB
OCDR
Read/Write
R/W
Initial Value
0
0000
0
Bit
7
65432
10
JTD
–JTRF
WDRF
BORF
EXTRF
PORF
MCUCSR
Read/Write
R/W
R
R/W
Initial Value
0
See Bit Description
相關PDF資料
PDF描述
MR80C52XXX-36P883R 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQCC44
MQ80C52XXX-36SHXXX 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
MC80C32E-16SHXXX:D 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
MR80C52XXX-36SCD 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQCC44
MD80C32-16SHXXX 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MC-80C32E-30 制造商:AIMTEC 制造商全稱:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller
MC-80C32E-30-E 制造商:AIMTEC 制造商全稱:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller
MC80D21000G 制造商:COR 功能描述:RN
MC80F0104 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0104B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS