參數資料
型號: MC80C32-36SC
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 36 MHz, MICROCONTROLLER, CDIP40
封裝: 0.600 INCH, SIDE BRAZED, DIP-40
文件頁數: 132/132頁
文件大?。?/td> 10886K
代理商: MC80C32-36SC
9
7593L–AVR–09/12
AT90USB64/128
2.2.8
Port E (PE7..PE0)
Port E is an 8-bit bidirectional I/O port with internal pull-up resistors (selected for each bit). The
Port E output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port E pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port E also serves the functions of various special features of the AT90USB64/128 as listed on
2.2.9
Port F (PF7..PF0)
Port F serves as analog inputs to the A/D Converter.
Port F also serves as an 8-bit bidirectional I/O port, if the A/D Converter is not used. Port pins
can provide internal pull-up resistors (selected for each bit). The Port F output buffers have sym-
metrical drive characteristics with both high sink and source capability. As inputs, Port F pins
that are externally pulled low will source current if the pull-up resistors are activated. The Port F
pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the
JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will
be activated even if a reset occurs.
Port F also serves the functions of the JTAG interface.
2.2.10
D-
USB Full speed / Low Speed Negative Data Upstream Port. Should be connected to the USB D-
connector pin with a serial 22
Ω resistor.
2.2.11
D+
USB Full speed / Low Speed Positive Data Upstream Port. Should be connected to the USB D+
connector pin with a serial 22
Ω resistor.
2.2.12
UGND
USB Pads Ground.
2.2.13
UVCC
USB Pads Internal Regulator Input supply voltage.
2.2.14
UCAP
USB Pads Internal Regulator Output supply voltage. Should be connected to an external capac-
itor (1F).
2.2.15
VBUS
USB VBUS monitor and OTG negociations.
2.2.16
RESET
Reset input. A low level on this pin for longer than the minimum pulse length will generate a
reset, even if the clock is not running. The minimum pulse length is given in Table 9-1 on page
58. Shorter pulses are not guaranteed to generate a reset.
2.2.17
XTAL1
Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
相關PDF資料
PDF描述
MR80C52XXX-36P883R 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQCC44
MQ80C52XXX-36SHXXX 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
MC80C32E-16SHXXX:D 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
MR80C52XXX-36SCD 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQCC44
MD80C32-16SHXXX 8-BIT, 16 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MC-80C32E-30 制造商:AIMTEC 制造商全稱:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller
MC-80C32E-30-E 制造商:AIMTEC 制造商全稱:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller
MC80D21000G 制造商:COR 功能描述:RN
MC80F0104 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0104B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS