- 您現在的位置：買賣IC網 > PDF目錄1950 > MC74VHC4316DTG (ON Semiconductor)IC MUX/DEMUX QUAD 1X1 16TSSOP PDF資料下載
參數資料
| 型號： | MC74VHC4316DTG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 12/12頁 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX QUAD 1X1 16TSSOP |
| 標準包裝： | 96 |
| 系列： | 74VHC |
| 功能： | 多路復用器/多路分解器 |
| 電路： | 4 x 1:1 |
| 導通狀態電阻： | 110 歐姆 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±2 V ~ 6 V |
| 電流 - 電源： | 40µA |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
MC74VHC4316
http://onsemi.com
9
APPLICATIONS INFORMATION
0
-10
-20
-30
-40
-50
- 100
1.0
2.0
FREQUENCY (kHz)
dBm
-60
-70
-80
-90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 14. Plot, Harmonic Distortion
3.0
The Enable and Control pins should be at VCC or GND
logic levels, VCC being recognized as logic high and GND
being recognized as a logic low. Unused analog
inputs/outputs may be left floating (not connected).
However, it is advisable to tie unused analog inputs and
outputs to VCC or VEE through a low value resistor. This
minimizes crosstalk and feedthrough noise that may be
picked up by the unused I/O pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and VEE. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below VEE. In the example
below, the difference between VCC and VEE is 12 V.
Therefore, using the configuration in Figure 15, a maximum
analog signal of twelve volts peaktopeak can be
controlled.
When voltage transients above VCC and/or below VEE are
anticipated on the analog channels, external diodes (Dx) are
recommended as shown in Figure 16. These diodes should
be small signal, fast turnon types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
MOSORBs (MOSORB
t is an acronym for high current
surge protectors). MOSORBs are fast turnon devices
ideally suited for precise dc protection with no inherent wear
out mechanism.
ANALOG O/I
ON
16
VCC = 6 V
ANALOG I/O
+ 6 V
-6 V
+ 6 V
-6 V
ENABLE CONTROL
INPUTS
(VCC OR GND)
ON
16
VCC
Dx
VCC
Dx
Figure 15.
Figure 16. Transient Suppressor Application
8
SELECTED
CONTROL
INPUT
Dx
SELECTED
CONTROL
INPUT
+ 6 V
VEE
-6 V
VCC
VEE
ENABLE CONTROL
INPUTS
(VCC OR GND)
VEE
相關PDF資料 |
PDF描述 |
|---|---|
| MC75174BDWR2G | IC LINEDRVR QUAD EIA485 20-SOICW |
| MC8610VT1333JB | MPU E600 CORE 1333MHZ 783-PBGA |
| MC8640DHX1000HE | IC DUAL CORE PROCESSOR 1023-CBGA |
| MC8641DTVU1250HE | IC MPU DUAL CORE E600 1023FCCBGA |
| MC8641VU1500KE | IC MPU DUAL CORE E600 994FCCBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC74VHC4316DTR2 | 功能描述:模擬開關 IC LOG CMOS QUAD MX/DEMX RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MC74VHC4316DTR2G | 功能描述:多路器開關 IC LOG CMOS QUAD MX/DEMX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC74VHC4316M | 功能描述:開關 IC - 各種 LOG CMOS QUAD MX/DEMX RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel |
| MC74VHC4316MEL | 功能描述:開關 IC - 各種 LOG CMOS QUAD MX/DEMX RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel |
| MC74VHC4316MELG | 功能描述:開關 IC - 各種 LOG CMOS QUAD MX/DEMX RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。