參數資料
型號： MC68HC705P6ACDW
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： HCMOS Microcontroller Unit
中文描述： 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
封裝： SOIC-28
文件頁數： 87/130頁
文件大?。?/td> 1541K
代理商： MC68HC705P6ACDW
EPROM
Programming from an External Memory Device
MC68HC705P6A
—
Rev. 2.0
Advance Information
MOTOROLA
EPROM
87
10.8 Programming from an External Memory Device
In this programming mode, PC5 must be connected to V
SS
. PC4 and
PC3 are used to select the programming mode. The programming circuit
shown in
Figure 10-2
uses an external 12-bit counter to address the
memory device containing the code to be copied. This counter requires
a clock and a reset function. The 12-bit counter can address up to
4 Kbytes of memory, which means that a port pin has to be used to
address the remaining 4 K of the 8-K memory space.
The following procedure explains how to use the programming circuit
shown in
Figure 10-2
to copy a user program from an external memory
device into the MCU
’
s EPROM:
1.
Program a 2764-type EPROM device with the desired instructions
and data. Code programmed into the 2764 must appear at the
same addresses desired in the MC68HC705P6A. Therefore, the
page zero code must start at $0020 and end at $004F, the main
body of code must start at $0100 and end at $12FF, and the user
vectors must start at $1FF0 and end at $1FFF.
NOTE:
The MOR data must appear at $1EFF and $1F00.
2.
Install the programmed 2764 device into the programming circuit.
3.
Install the MC68HC705P6A to be programmed into the
programming circuit.
4.
Set the PROGRAM and/or VERIFY switches for the desired
operation (an open switch is the active state) and close the
RESET switch to hold the MCU in reset.
5.
Make sure that the V
PP
source is OFF.
Apply the V
DD
source to the programming circuit.
Apply the V
PP
source to the programming circuit.
Open the RESET switch to allow the MCU to come out of reset
and begin execution of the software in its internal bootloader
ROM.
6.
7.
8.
相關PDF資料
PDF描述
MC68HC705P6ACP HCMOS Microcontroller Unit
MC68HC912D60A Microcontrollers
MC68HC912D60C Microcontrollers
MC68HC912D60P Microcontrollers
MC68VZ328P Integrated Portable System Processor Product Brief
相關代理商/技術參數
參數描述
MC68HC705P6ACP 功能描述:IC MCU 2.1MHZ 4.5K OTP 28-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC705P6ADW 制造商:Rochester Electronics LLC 功能描述:MCU, 176 BYTES RAM, A/D - Bulk
MC68HC705P6AMDW 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705P6AMP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705P6CDW 制造商:Motorola Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*