參數資料
型號： MC68HC11D0CFB2
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44
封裝： QFP-44
文件頁數： 64/138頁
文件大?。?/td> 1047K
代理商： MC68HC11D0CFB2
Programmable Read-Only Memory (PROM)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
31
ROMON — PROM Enable Bit
This bit is set out of reset, enabling the EPROM or OTPROM in all modes. This bit is writable once in
normal modes (SMOD = 0), but is writable at any time in special modes (SMOD = 1).
1 = PROM is present in the memory map.
0 = PROM is disabled from the memory map.
NOTE
In expanded mode out of reset, the EPROM or OTPROM is located at
$7000–$7FFF. In all other modes, the PROM resides at $F000–$FFFF.
2.4 Programmable Read-Only Memory (PROM)
The MC68HC711D3 has 4-Kbytes of one-time programmable read-only memory (OTPROM). The PROM
address is $F000–$FFFF in all modes except expanded multiplexed. In expanded- multiplexed mode, the
PROM is located at $7000–$7FFF after reset.
The on-chip read-only memory (ROM) of an MC68HC711D3 is programmed in MCU mode. In this mode,
the PROM is programmed through the MCU in the bootstrap or test modes. The erased state of a PROM
byte is $FF.
Using the on-chip OTPROM programming feature requires an external 12-volt nominal power supply
(VPP). Normal programming is accomplished using the OTPROM programming register (PPROG).
As described in the following subsections, these two methods of programming and verifying EPROM are
possible:
1.
Programming an individual EPROM address
2.
Programming the EPROM with downloaded data
2.4.1 Programming an Individual EPROM Address
In this method, the MCU programs its own EPROM by controlling the PPROG register. Use these
procedures to program the EPROM through the MCU with:
The ROMON bit set in the CONFIG register
The 12-volt nominal programming voltage present on the XIRQ/VPP pin
The IRQ pin must be pulled high.
EPROG
LDAB
#$20
STAB
$003B
Set ELAT bit (PGM = 0) to enable
EPROM latches.
STAA
$0,X
Store data to EPROM address
LDAB
#$21
STAB
$003B
Set PGM bit with ELAT = 1 to enable
EPROM programming voltage
JSR
DLYEP
Delay 2–4 ms
CLR
$003B
Turn off programming voltage and set
to READ mode
相關PDF資料
PDF描述
MC68HC11D3CFN2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44
MC68HC711D3CP3 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP40
MC68HC11D3CFN3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44
MC68HC11D3CFB1 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44
MC68L11D0CFB3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68HC11D0CFB3 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC11D0CFB3R2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC11D0CFBE2 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFBE3 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFBE3R 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*