<button id="bz37z"><input id="bz37z"></input></button>
  • 參數資料
    型號: MC68HC11A1VFU2
    廠商: MOTOROLA INC
    元件分類: 微控制器/微處理器
    英文描述: HCMOS Single-Chip Microcontroller
    中文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQFP64
    封裝: QFP-64
    文件頁數: 53/158頁
    文件大?。?/td> 503K
    代理商: MC68HC11A1VFU2
    MC68HC11A8
    TECHNICAL DATA
    SERIAL COMMUNICATIONS INTERFACE
    MOTOROLA
    5-9
    5
    TCIE — Transmit Complete Interrupt Enable
    0 = TC interrupts disabled
    1 = SCI Interrupt if TC = 1
    RIE — Receive Interrupt Enable
    0 = RDRF and OR interrupts disabled
    1 = SCI interrupt if RDRF or OR = 1
    ILIE — Idle Line Interrupt Enable
    0 = IDLE interrupts disabled
    1 = SCI interrupt if IDLE = 1
    TE — Transmit Enable
    When the transmit enable bit is set, the transmit shift register output is applied to the
    TxD line. Depending on the state of control bit M (SCCR1), a preamble of 10 (M = 0)
    or 11 (M = 1) consecutive ones is transmitted when software sets the TE bit from a
    cleared state. After loading the last byte in the serial communications data register and
    receiving the TDRE flag, the user can clear TE. Transmission of the last byte will then
    be completed before the transmitter gives up control of the TxD pin. While the trans-
    mitter is active, the data direction register control for port D bit 1 is overridden and the
    line is forced to be an output.
    RE — Receive Enable
    When the receive enable bit is set, the receiver is enabled. When RE is clear, the re-
    ceiver is disabled and all of the status bits associated with the receiver (RDRF, IDLE,
    OR, NF, and FE) are inhibited. While the receiver is enabled, the data direction register
    control for port D bit 0 is overridden and the line is forced to be an input.
    RWU — Receiver Wake Up
    When the receiver wake-up bit is set by the user’s software, it puts the receiver to
    sleep and enables the “wake up” function. If the WAKE bit is cleared, RWU is cleared
    by the SCI logic after receiving 10 (M = 0) or 11 (M = 1) consecutive ones. If the WAKE
    bit is set, RWU is cleared by the SCI logic after receiving a data word whose MSB is
    set.
    SBK — Send Break
    If the send break bit is toggled set and cleared, the transmitter sends 10 (M = 0) or 11
    (M = 1) zeros and then reverts to idle or sending data. If SBK remains set, the trans-
    mitter will continually send whole blocks of zeros (sets of 10 or 11) until cleared. At the
    completion of the break code, the transmitter sends at least one high bit to guarantee
    recognition of a valid start bit. If the transmitter is currently empty and idle, setting and
    clearing SBK is likely to queue two character times of break because the first break
    transfers almost immediately to the shift register and the second is then queued into
    the parallel transmit buffer.
    相關PDF資料
    PDF描述
    MC68HC11E0CB2 Microcontrollers
    MC68S711E9CFN2 Microcontrollers
    MC68HC711E20FS3 Microcontrollers
    MC68L11E20FU2 Microcontrollers
    MC68L11E0FU2 Microcontrollers
    相關代理商/技術參數
    參數描述
    MC68HC11A1VP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
    MC68HC11A1VP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
    MC68HC11A8 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
    MC68HC11A8BCFN2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
    MC68HC11A8BCFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller