- 您現在的位置：買賣IC網 > PDF目錄382306 > MC44603A (ON SEMICONDUCTOR) RV Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 3.3V; Output Voltage (Vdc): 15V; Power: 2W; High Isolation 2W Converter; Approved for Medical Applications; EN and UL Safety Certificates; 6kVDC Isolation; Skinny DIP24 Package; Optional Continuous Short Circuit Protected; Fully Encapsulated; Very Low Isolation Capacitance PDF資料下載
參數資料
| 型號： | MC44603A |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | DC/DC變換器 |
| 英文描述： | RV Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 3.3V; Output Voltage (Vdc): 15V; Power: 2W; High Isolation 2W Converter; Approved for Medical Applications; EN and UL Safety Certificates; 6kVDC Isolation; Skinny DIP24 Package; Optional Continuous Short Circuit Protected; Fully Encapsulated; Very Low Isolation Capacitance |
| 中文描述： | 混合頻率模式二七二三六七六七的PWM控制器 |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 405K |
| 代理商： | MC44603A |
MC44603A
17
MOTOROLA ANALOG IC DEVICE DATA
Maximum Duty Cycle and Soft–Start Control
Maximum duty cycle can be limited to values less than
80% by utilizing the Dmax and soft–start control. As depicted
in Figure 42, the Pin 11 voltage is compared to the oscillator
sawtooth.
Figure 42. Dmax and Soft–Start
CDmax
11
Soft–Start
Capacitor
VOSC
Oscillator
Dmax
Output
Drive
Output
Control
0.4 Iref
Vref
2.4 V
DZ
Figure 43. Maximum Duty Cycle Control
Voltage
Dmax
Pin 11
VCT
(Pin 10)
Using the internal current source (0.4 Iref), the Pin 11
voltage can easily be set by connecting a resistor to this pin.
If a capacitor is connected to Pin 11, the voltage increases
from 0 to its maximum value progressively (refer to Figure
44), thereby, implementing a soft–start. The soft–start
capacitor is discharged internally when the VCC (Pin 1)
voltage drops below 9.0 V.
Figure 44. Different Possible Uses of Pin 11
Pin 11
RI
RI
R Connected to Pin 11
I = 0.4 Iref
VZ
VZ
C
C // R
τ
= RC
If no external component is connected to Pin 11, an
internal zener diode clamps the Pin 11 voltage to a value VZ
that is higher than the oscillator peak value, disabling
soft–start and maximum duty cycle limitation.
Foldback
As depicted in Figures 32 and 48, the foldback input (Pin
5) can be used to reduce the maximum VCS value, providing
foldback protection. The foldback arrangement is a
programmable peak current limitation.
If the output load is increased, the required converter peak
current becomes higher and VCS increases until it reaches its
maximum value (normally, VCS max = 1.0 V).
Then, if the output load keeps on increasing, the system is
unable to supply enough energy to maintain the output
voltages in regulation. Consequently, the decreasing output
can be applied to Pin 5, in order to limit the maximum peak
current. In this way, the well known foldback characteristic
can be obtained (refer to Figure 45).
Figure 45. Foldback Characteristic
Vout
VO
Nominal
VCC
Vdisable2
Ipk max
New Startup
Sequence Initiated
Iout
Overload
NOTE:
Foldback is disabled by connecting Pin 5 to VCC.
Overvoltage Protection
The overvoltage arrangement consists of a comparator
that compares the Pin 6 voltage to Vref (2.5 V) (refer to
Figure 46).
If no external component is connected to Pin 6, the
comparator noninverting input voltage is nearly equal to:
2.0 k
11.6 k
The comparator output is high when:
2.0 k
x VCC
2.0 k
11.6 k
2.0 k
VCC
x VCC
2.5 V
17 V
A delay latch (2.0
μ
s) is incorporated in order to sense
overvoltages that last at least 2.0
μ
s.
If this condition is achieved, VOVP out, the delay latch
output, becomes high. As this level is brought back to the
input through an OR gate, VOVP out remains high (disabling
the IC output) until Vref is disabled.
Consequently, when an overvoltage longer than 2.0
μ
s is
detected, the output is disabled until VCC is removed and
then re–applied.
The VCC is connected after Vref has reached steady state
in order to limit the circuit startup consumption.
The overvoltage section is enabled 5.0
μ
s after the
regulator has started to allow the reference Vref to stabilize.
By connecting an external resistor to Pin 6, the threshold
VCC level can be changed.
Figure 46. Overvoltage Protection
VCC
Vref
0
T
VOVP
External
Resistor
2.5 V
(Vref)
2.0 k
11.6 k
2.5 V
5.0
μ
s
VOVP out
2.0
μ
s
(If VOVP out = 1.0,
the Output is Disabled)
In
Out
Delay
τ
Enable
COVLO
6
Delay
In
Out
τ
相關PDF資料 |
PDF描述 |
|---|---|
| MC44603ADW | MIXED FREQUENCY MODE GREENLINE PWM CONTROLLER |
| MC44603AP | MIXED FREQUENCY MODE GREENLINE PWM CONTROLLER |
| MC44604 | High Safety Pulsed Mode Stanby GreenLine PWM Controller |
| MC44604P | RV Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 3.3V; Output Voltage (Vdc): 3.3V; Power: 2W; High Isolation 2W Converter; Approved for Medical Applications; EN and UL Safety Certificates; 6kVDC Isolation; Skinny DIP24 Package; Optional Continuous Short Circuit Protected; Fully Encapsulated; Very Low Isolation Capacitance |
| MC44605 | High Safety, Latched Mode, GreenLine PWM Controller for (Multi)Synchronized Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC44603A_05 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Enhanced Mixed Frequency Mode GreenLine TM PWM Controller:Fixed Frequency, Variable Frequency,Standby Mode |
| MC44603ADW | 功能描述:電流型 PWM 控制器 Voltage/Current PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC44603ADWG | 功能描述:電流型 PWM 控制器 ANA SMPS PWM FREQ CONT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC44603ADWR2 | 功能描述:電流型 PWM 控制器 Voltage/Current PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC44603ADWR2G | 功能描述:電流型 PWM 控制器 ANA SMPS PWM FREQ CONT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。