- 您現在的位置：買賣IC網 > PDF目錄382305 > MC3PHACVP (MOTOROLA INC) 3-Phase AC Motor Controller PDF資料下載
參數資料
| 型號： | MC3PHACVP |
| 廠商： | MOTOROLA INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3-Phase AC Motor Controller |
| 中文描述： | AC MOTOR CONTROLLER, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 38/44頁 |
| 文件大小： | 724K |
| 代理商： | MC3PHACVP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MC3PHAC/D
38
3-Phase AC Motor Controller
MOTOROLA
RevSteady
—
This state is entered from the RevAccel state after the
actual motor speed has reached the requested speed defined by the
Speed In variable. In this state, the motor is held at a constant reverse
speed.
RevDecel
— This state is entered from the RevAccel or RevSteady
states whenever a CmdStop or CmdFwd command is received. This
state can also be entered from the RevSteady state if the Speed In
variable is decreased below the actual current speed. In this state, the
motor is decelerated in reverse according to the chosen parameters.
SetBaseFreq
— This state is entered from any state whenever a
CmdBaseFreqxx command is received. In this state, the motor
frequency at which full voltage is applied is configured and the state is
then automatically exited and the original state is re-entered.
SetAccel
— This state is entered from any state whenever a write to the
Acceleration variable occurs. In this state, the motor acceleration is
configured and the state is then automatically exited and the original
state is re-entered.
SetSpeed
— This state is entered from any state whenever a write to
the Speed In variable occurs. In this state, the requested motor speed is
configured and the state is then automatically exited and the original
state is re-entered.
Fault
— This state is entered from any state whenever a fault condition
occurs (see
Fault Protection
on
page 16
). In this state, the PWM
outputs are driven off (unless the fault state was entered from the
PWMHighZ state, in which case, the PWM outputs remain in the High Z
state). When the problem causing the fault condition is removed, a timer
is started which will wait a specified amount of time (which is user
programmable) before exiting this state. Under normal operating
conditions, this timeout will cause the Fault state to be automatically
exited to the PWM0RPM state, where motion will once again be initiated
if a CmdFwd or CmdRev has been received. The exceptions to this rule
are the cases when the Fault state was entered from the PWMHighZ or
PWMOFF states, in which case, exiting from the Fault state will return
back to these states.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC3S12C128 | 16-Bit Microcontroller |
| MC3S12C32 | 16-Bit Microcontroller |
| MC3S12C64 | 16-Bit Microcontroller |
| MC3S12C96 | 16-Bit Microcontroller |
| MC3S12GC32 | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC3PHACVPE | 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC3S12C128 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C32 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C64 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C96 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。