- 您現在的位置：買賣IC網 > PDF目錄1948 > MC33780EG (Freescale Semiconductor)IC DBUS MASTER DUAL DIFF 16-SOIC PDF資料下載
參數資料
| 型號： | MC33780EG |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 18/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DBUS MASTER DUAL DIFF 16-SOIC |
| 標準包裝： | 47 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
33780
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
When enable is true and there is at least one valid entry in
the transmit FIFO, the DBUS frame signal is driven low to
start a frame. States WAIT_SIG_DLY_0 through
WAIT_SIG_DLY_2 create a one DBUS bit-time delay before
the start of the first data bit. After WAIT_SIG_DLY_2, the
DBUS_BIT_PTR gets initialized to the total word length, as
determined by the MSx, SWLENx, and CRCLENx bits. The
XFER_DBUS_BIT_0 state is then entered.
XFER_DBUS_BIT_0 through XFER_DBUS_BIT_2 form a
loop where each pass corresponds to one DBUS bit time.
During the first third of the bit the DSIxS signal is low, during
the second third DSIxS is low for a zero or high for a one,
during the last third of the bit time DSIxS is high. Provided this
is not the end of the last CRC bit, the bit pointer is
decremented and the loop is repeated.
After the last CRC bit, the DBUS_R_PUSH state is
entered. This state ensures that the CRC flag is stable prior
to adjusting the receive (and transmit) FIFO pointers. The
DBUS_X_POP state prevents an X_FIFO_POP from
occurring at the same time as an R_FIFO_PUSH.
After DBUS_X_POP, the state transitions back to the
WAIT_FRAME_DLY state. This state ensures proper frame
spacing is allowed to charge up the storage capacitors in
remote nodes. Notice that the delay counter was reset at the
end of the last CRC bit so the delay period can start to time
out even while the DBUS_R_PUSH and DBUS_X_POP
states are being processed.
Figure 22 describes the operation of the transmit FIFO.
This FIFO is four levels deep, including the stage which is
written into by the SPI and the stage which provides the data
for the current DBUS serial transfer. State transitions in this
state machine occur at the trailing edges of X_FIFO_PUSH
and X_FIFO_POP.
When this FIFO is completely empty, the SPI can write
four new values to fill the FIFO without waiting for any action
on the DBUS side of the FIFO. Values are pushed into the
FIFO from the SPI interface and values are popped after they
have been serially sent out of the DBUS interface. When the
FIFO is full, additional attempts to write new data from the
SPI side are ignored (the host MCU should be sure the
TFNFx status bit is set before writing more data to the FIFO).
Reset, abort, or enable going to zero causes
asynchronous entry to the TX_IDLE state, which
corresponds to the FIFO empty condition. The push and pop
pointers are cleared and X_FIFO_EMPTY is set to true.
X_FIFO_PUSH causes the push pointer to be incremental,
X_FIFO_EMPTY to be set to false, and the state to transition
to TX_NOT_EMPTY. The push request comes from the SPI
transfer state machine after a new value has been written into
the FIFO.
Figure 21. State Diagram of DBUS Transfer
STATE TRANSISITONS OCCUR
ON POS EDGE OF SCALED
DBUS 1/3RD BIT CLOCK
WAIT_FRAME_DLY
WAIT_SIG_DLY_0
WAIT_SIG_DLY_1
WAIT_SIG_DLY_2
XFER_DBUS_BIT_0
XFER_DBUS_BIT_1
XFER_DEBUS_BIT_2
DBUS_X_POP
DBUS_R_PUSH
R_FIFO_PUSH = 0;
X_FIFO_POP = 0;
DSIS = DATA;
DSIS = 1;
DELAY_OVER &
X_FIFO_NOT_EMPTY/
DSIF = 0;
WAIT_SIG_DLY[0..2] CAUSES 1 BIT-TIME DLY TO 1ST BIT FALLING EDGE
~LAST_CRC_BIT/
DBUS_BIT_PTR = DBUS_BIT_PTR-1;
DSIS = 0;
LAST_CRC-BIT/
DSIF = 1, DSIS = 1;
RESET DELAY_CNR;
R_FIFO_PUSH = 1
X_FIFO_POP = 1;
DBUS_BIT_PTR = 8 to 15, OR 23;
DSIS = 0;
RSTB ACTIVE or ABORT or ~EN/
DSIF = 1, DSIS = 1;
RESET_DELAY_CNTR;
相關PDF資料 |
PDF描述 |
|---|---|
| MC33790DW | IC DSI 2-CHAN INTERFACE 16-SOIC |
| MC33794EKR2 | IC SENSOR ELECTRIC FIELD 54SOICW |
| MC33889BDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33889DPEG | IC SYSTEM BASE W/CAN 28SOIC |
| MC33972TEWR2 | IC SWITCH DETECT SPI 32-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33780EGR2 | 功能描述:IC DBUS MASTER DUAL DIFF 16-SOIC RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| MC33790DW | 功能描述:IC DSI 2-CHAN INTERFACE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC33790HEG | 功能描述:接口 - 專用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33790HEGR2 | 功能描述:接口 - 專用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33793D | 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。