參數資料
型號: MC33742
廠商: 飛思卡爾半導體(中國)有限公司
元件分類: CAN
英文描述: System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(帶增強型高速CAN收發器的系統基片)
中文描述: 系統基礎芯片的增強型(SBC)的高速CAN收發器(帶增強型高速的CAN收發器的系統基片)
文件頁數: 25/52頁
文件大?。?/td> 1087K
代理商: MC33742
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33742
25
Figure 11. Behavior at 33742 Power-Up
Debug Mode: Hardware and Software Debug with the
33742
When the 33742 is mounted on the same printed circuit
board as the MCU it supplies, both application software and
33742 dedicated routines must be debugged. The following
features permit software debugging by allowing the possibility
of disabling the 33742 internal software watchdog timer.
Device Power-Up, Reset Terminal Connected to V
DD
At 33742 power-up, V
DD
voltage is provided; however, if no
SPI communication occurs to configure the device, a reset
occurs every 350 ms. In order to allow software debug and
avoid MCU reset, the
RST
terminal can be connected directly to
V
DD
by a jumper.
Debug Modes with Software Watchdog Disabled Though
SPI (Normal Debug, Standby Debug, and Stop Debug)
The watchdog software can be disabled through SPI. To
avoid unwanted watchdog disable while limiting the risk of
disabling the watchdog during 33742 normal operation,
watchdog disable must be done using the following sequence:
Step 1–Power down the 33742.
Step 2–Power up the 33742. This sets the BATFAIL bit,
allowing the 33742 to enter Normal Request mode.
Step 3–Write to the TIM1 subregister to allow the 33742
to enter Normal mode.
Step 4–Write to the MCR register with data 0000. This
enables the debug mode. Complete SPI byte is
0001 0000.
Step 5–Write to the MCR register normal debug. SPI byte
is 0001 x101.
Important
While in debug mode, the 33742 can be used
without having to clear the watchdog on a regular basis to
facilitate software and hardware debug.
Step 6–To leave the debug mode, write 0000 to the MCR
register.
At Step 2, the 33742 is in Normal Request. Steps 3, 4, and 5
should be completed consecutively and within the 350 ms time
period of the Normal Request mode. If not, the 33742 will go
into Reset mode and enter Normal Request again.
Figure 12,
page 26, illustrates debug mode selection.
Power-Up
Reset
Normal
Request
Normal
Trigger
Batfail
No Stop
Sleep
No
No
Yes
No
Yes
Yes
Behavior after power-up if no trigger appears
Behavior after reset of BATFAIL if no trigger appears
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC33790 Two-Channel Distributed System Interface (DSI) Physical Interface Device(2通道分布式系統接口(DSI)物理接口)
MC33793 Distributed System Interface (DSI) Sensor Interface(分布式系統接口(DSI)傳感器接口)
MC33794 Electric Field Imaging Device(電場成像設備)
MC33880 Configurable Octal Serial Switch with Serial Peripheral Interface I/O(可配置的8串行開關,帶串行外圍I/O口(SPI))
MC33882 Six-Output Low-Side Switch with SPI and Parallel Input Control(帶SPI和并口輸入控制的6輸出低端開關)
相關代理商/技術參數
參數描述
MC33742DW 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33742DWR2 功能描述:網絡控制器與處理器 IC SBC-E-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33742EP 功能描述:CAN 接口集成電路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742EPR2 功能描述:CAN 接口集成電路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33742PEG 功能描述:CAN 接口集成電路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube