- 您現在的位置：買賣IC網 > PDF目錄385566 > MC1H3 (Microchip Technology Inc.) High Voltage Power Module Users Guide PDF資料下載
參數資料
| 型號： | MC1H3 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | High Voltage Power Module Users Guide |
| 中文描述： | 高壓電源模塊用戶指南 |
| 文件頁數： | 28/60頁 |
| 文件大?。?/td> | 1522K |
| 代理商： | MC1H3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
dsPICDEM MC1H 3-Phase High Voltage Power Module
DS70096A-page 22
2003 Microchip Technology Inc.
The third device (U2) is on the positive DC input connection from the rectifier within
the input power stage (see Figure 1-1). This is configured to have 2 turns of wire
through it as delivered with LK2 installed. This gives a maximum sensed current of
9.6A and a gain of 4.8A/V. U2 serves two purposes. First, is to provide the required
current feedback information for controlling the active power factor correction (PFC)
switches. The second purpose is to provide detection of ground current faults (i.e.,
when one or more of the inverter outputs become incorrectly connected to ground).
1.4.6
Shunt Feedback (Appendix A, Sheet 3)
1.4.6.1
INTRODUCTION
In many applications, the cost of isolated current transducers is prohibitive or the
isolation is not required. In these instances, it is common practice to use resistive
shunts. The shunts can be placed in series with the output connections but this
inevitably requires the use of level-shifting and the creation of floating power supplies.
Therefore, it is common to have shunts referenced to the same potential as the low
voltage power supplies which is invariably the -DC bus. The disadvantage of using
shunts referenced to the “l(fā)ow side” is that the feedback information is only available
during certain portions of the PWM cycle. In order to extract the required information,
the shunts must be sampled at precise intervals. This feature has been allowed for in
the dsPIC device by the inclusion of sample and hold amplifiers in the ADC module
that can be triggered from the PWM module (see the
dsPIC30F Family Reference
Manual
for details).
On high voltage low power systems, it may be possible to use shunts of high enough
value to have sufficient voltage for direct input to an ADC. More commonly, the
dissipation in the shunt dictates the use of low resistance values and appropriate
amplification. If too high, the voltage drop across the shunt can also cause problems
for driving the power transistors. For low gains, it may be possible to use single-ended
amplification. Differential amplification is required as the gains increase in order to
provide a signal of sufficient quality and accuracy.
The Microchip MCP6022 (dual) and MCP6024 (quad) parts have been used in the
design for providing the differential amplification. They are an ideal choice for the
following reasons:
Low power consumption (1 mA typical/amp) – this is especially important where
the power supplies are derived from the DC bus with a resistor/zener network.
Low offset voltage (0.5 mV max.).
Rail-rail inputs and outputs.
No gain inversion with negative inputs – this is important as it is common for the
amplifier to have negative spikes on its inputs that occur during switching events
due to the shunt's inductance. Gain inversion can lead to current control instability
and false tripping of protection circuits.
High gain bandwidth product (10 MHz typical) – this is often a more important
factor in determining the speed of response than slew rate in this application, due
to the requirements to amplify rapidly changing signals of low amplitude.
Note that in applications requiring less gain and/or slower speed of response, the
MCP602/604 family offers a good alternative with even lower power supply
consumption.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33023DWG | High Speed Single−Ended PWM Controller |
| MC33023DWR2 | High Speed Single−Ended PWM Controller |
| MC33023DWR2G | High Speed Single−Ended PWM Controller |
| MC33025DWG | High Speed Double−Ended PWM Controller |
| MC33025DWR2 | High Speed Double−Ended PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1JJN0600 | 功能描述:環形公制連接器 M40 C Straight 6 Position Extension RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1JJN0800 | 功能描述:環形公制連接器 M40 C Straight Extension 8 Pos. RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1LKN0600 | 功能描述:環形公制連接器 M40 C Straight Recpt 6 Position RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1LKN0800 | 功能描述:環形公制連接器 M40 C Straight Recpt 8 Position RoHS:否 制造商:3M Electronic Solutions Division 產品類型:Connectors 系列:M12 外殼類型:Plug 觸點數量:4 安裝風格:Cable 端接類型:Solder Cup 電流額定值:4 A |
| MC1M | 制造商:G & J HALL 功能描述:STEP DRILL 4-12MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 4-12MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 4-12MM, 1MM STEP; Drill Bit Size Metric:4mm; Overall Length:75.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:5mm; Range:4mm - 12mm; Range:4mm - 12mm; Shank Dia:6mm; S ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。