- 您現在的位置：買賣IC網 > PDF目錄224197 > MBM29DL162BD-70PFTN (FUJITSU LTD) 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF資料下載
參數資料
| 型號： | MBM29DL162BD-70PFTN |
| 廠商： | FUJITSU LTD |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封裝： | PLASTIC, TSOP1-48 |
| 文件頁數： | 31/74頁 |
| 文件大小： | 1170K |
| 代理商： | MBM29DL162BD-70PFTN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
MBM29DL16XTD/BD-70/90
37
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm
or sector erase time-out. (See “Hardware Sequence Flags Table”.)
See “(6) AC Waveforms for Data Polling during Embedded Algorithm Operations” in sTIMING DIAGRAM for the
Data Polling timing specifications and diagrams.
DQ6
Toggle Bit I
The MBM29DL16XTD/BD also feature the “Toggle Bit I” as a method to indicate to the host system that the
Embedded Algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (OE toggling) data from
the devices will result in DQ6 toggling between one and zero. Once the Embedded Program or Erase Algorithm
cycle is completed, DQ6 will stop toggling and valid data will be read on the next successive attempts. During
programming, the Toggle Bit I is valid after the rising edge of the fourth write pulse in the four write pulse sequence.
For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth write pulse in the six
write pulse sequence. The Toggle Bit I is active during the sector time out.
In programming, if the sector being written to is protected, the toggle bit will toggle for about 1
s and then stop
toggling without the data having changed. In erase, the devices will erase all the selected sectors except for the
ones that are protected. If all selected sectors are protected, the chip will toggle the toggle bit for about 400 s
and then drop back into read mode, having changed none of the data.
Either CE or OE toggling will cause the DQ6 to toggle. In addition, an Erase Suspend/Resume command will
cause the DQ6 to toggle.
The system can use DQ6 to determine whether a sector is actively erasing or is erase-suspended. When a bank
is actively erasing (that is, the Embedded Erase Algorithm is in progress), DQ6 toggles. When a bank enters the
Erase Suspend mode, DQ6 stops toggling. Successive read cycles during the erase-suspend-program cause
DQ6 to toggle.
To operate toggle bit function properly, CE or OE must be high when bank address is changed.
See “(7) AC Waveforms for Toggle Bit I during Embedded Algorithm Operations” in sTIMING DIAGRAM for the
Toggle Bit I timing specifications and diagrams.
DQ5
Exceeded Timing Limits
DQ5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under
these conditions DQ5 will produce a “1”. This is a failure condition which indicates that the program or erase
cycle was not successfully completed. Data Polling is the only operating function of the devices under this
condition. The CE circuit will partially power down the device under these conditions (to approximately 2 mA).
The OE and WE pins will control the output disable functions as described in “MBM29DL16XTD/BD User Bus
Operations Tables (BYTE = VIH and BYTE = VIL)” (in sDEVICE BUS OPERATION).
The DQ5 failure condition may also appear if a user tries to program a non blank location without erasing. In this
case the devices lock out and never complete the Embedded Algorithm operation. Hence, the system never
reads a valid data on DQ7 bit and DQ6 never stops toggling. Once the devices have exceeded timing limits, the
DQ5 bit will indicate a “1.” Please note that this is not a device failure condition since the devices were incorrectly
used. If this occurs, reset the device with command sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29LV008B-10PFTR | 1M X 8 FLASH 3V PROM, 100 ns, PDSO40 |
| MBR16100CT | 16 A, 100 V, SILICON, RECTIFIER DIODE, TO-220AB |
| MBR20100WT | 10 A, SILICON, RECTIFIER DIODE, TO-247AD |
| MBR30100PTP | 30 A, 100 V, SILICON, RECTIFIER DIODE, TO-247 |
| MBR3020WT-G | 30 A, SILICON, RECTIFIER DIODE, TO-247AD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29DL162BD-70PFTR | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BD-90PBT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BD-90PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BD-90PFTR | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL162BE | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT Dual Operation |
發布緊急采購，3分鐘左右您將得到回復。