參數資料
型號： MB91482PMC-GE1
元件分類： 微控制器/微處理器
英文描述： 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 20/92頁
文件大?。?/td> 2431K
代理商： MB91482PMC-GE1
MB91470/480 Series
DS07-16901-5E
27
Order of power turning ON/OFF
Use the following procedure for turning the power on or off. If not using the A/D converter, connect AVCC =VCC
and AVSS = VSS. Turn on the power supply in the sequence VCC
→ AVCC → AVRH, and turn off the power in
the reverse sequence.
Source oscillation input when turning on the power
When turning the power on, maintain the clock input until the device is released from the oscillation stabilization
wait state.
Cautions for operation during PLL clock mode
Even if the oscillator comes off or the clock input stops with the PLL clock selected for MB91470/480 series,
MB91470/480 series may continue to operate at the free-run frequency of the PLL’s internal self-oscillating
oscillator circuit.
Performance of this operation, however, cannot be guaranteed.
Using an external clock
When using an external clock, you must always input clock signals with opposite phase from X0 pin to X1 pin
simultaneously. However, as the X1 pin halts with an output at the "H" level during stop mode, insert a resistor
of approximately 1 k
externally to prevent a conflict between the two outputs if using stop mode (oscillation
stop mode).
The figure below shows an example of how to use an external clock.
C pin
As MB91470/480 series includes an internal regulator, always connect a bypass capacitor of approximately
4.7
F to the C pin for use by the regulator.
Software reset on the synchronous mode
Be sure to meet the following two conditions before setting 0 to the SRST bit of STCR (standby control register)
when the software reset is used on the synchronous mode.
Set the interrupt enable flag (I-Flag) to interrupts disabled (I-Flag=0).
Not used NMI
X0
X1
MB91470/480
series
Example of Using an External Clock
C
4.7
F
GND
VSS
MB91470/480
series
相關PDF資料
PDF描述
MB91F479PMC1-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
MB91F479BGL-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PBGA144
MB91F482PMC-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100
MB91487PF-GE1 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100
MB91F487PF-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB-9-156 功能描述:MOUNTING BUTTON 9/32 TO 11/32 RoHS:是 類別:硬件，緊固件，配件 >> 鉚釘 系列:MB 產品培訓模塊:Rivets and Hardware Engineering Technology Injection Molding and Plastics Plastic Materials 標準包裝:1,000 系列:SR 類型:卡入式 鉚釘直徑:0.197"（5.00mm） 接頭直徑:0.354"（8.99mm） 鉚釘長度:0.260"（6.60mm） 孔直徑:0.203"（5.16mm） 面板厚度:0.098 ~ 0.138"（2.49 ~ 3.51mm） 接頭高度:0.087"（2.21mm） 特點:阻燃 顏色:黑 材質:尼龍 其它名稱:61100367SRVO-5055 BSRVO-5055 B-NDSRVO5055B
MB91580 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Motor Control MCU for Electric (EV) and Hybrid Electric Vehicles (HEV)
MB91590 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit MCU with Integrated Graphics Controller SoC
MB91613PMC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers
MB-9-187 功能描述:MOUNTING BUTTON 9/32 TO 11/32 RoHS:是 類別:硬件，緊固件，配件 >> 鉚釘 系列:MB 產品培訓模塊:Rivets and Hardware Engineering Technology Injection Molding and Plastics Plastic Materials 標準包裝:1,000 系列:SR 類型:卡入式 鉚釘直徑:0.197"（5.00mm） 接頭直徑:0.354"（8.99mm） 鉚釘長度:0.260"（6.60mm） 孔直徑:0.203"（5.16mm） 面板厚度:0.098 ~ 0.138"（2.49 ~ 3.51mm） 接頭高度:0.087"（2.21mm） 特點:阻燃 顏色:黑 材質:尼龍 其它名稱:61100367SRVO-5055 BSRVO-5055 B-NDSRVO5055B
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*