- 您現在的位置：買賣IC網 > PDF目錄98010 > MB91233LPFF-G-XXX 32-BIT, MROM, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91233LPFF-G-XXX |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, MROM, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 8/56頁 |
| 文件大?。?/td> | 293K |
| 代理商： | MB91233LPFF-G-XXX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB91230 Series
16
About Oscillation Input at Power On
When turning the power on, maintain clock input untill the device is released from the oscillation stabilization
wait state.
Clock Control Block
Input the “L” signal to the INIT pin to assure the clock oscillation stabilization wait time.
Switch Shared Port Function
To switch between the use as a port and the use as a dedicated pin, use the port function register (PFR) .
Low Power Consumption Mode
To enter the standby mode, use the synchronous standby mode (set with the SYNCS bit as bit 8 in the TBCR :
timebse counter control register) and be sure to use the following sequence
In addition, please set I flag, ILM, and ICR to diverge to the interruption handler that is the return factor after the
standby returns.
Please do not do the following when the monitor debugger is used.
Break point setting for above instruction lines
Step execution for above instruction lines
Power-on sequence for dual-power-supply model
Notes on the power-on and power-off sequences
Power-on sequence : Vcc3B, Vcc3
→Vcc→Vcc3IO, AVRH, V0-V3
Power-off sequence : Vcc3IO, AVRH, V0-V3 Vcc3
→Vcc→Vcc3B, Vcc3
When VCC is turned on earlier, a potential difference between VCC and VCC3 must fall within 3.6 V.
The LCD power supply V3 must not exceed VCC in voltage. Apply V3 after turning on VCC3.
Turn on VCC3 before applying the analog power supply AVCC or an analog signal.
Notes on the PS register
As the PS register is processed by some instructions in advance, exception handling below may cause the
interrupt handling routine to break when the debugger is used or the display contents of flags in the PS register
to be updated.
As the microcontroller is designed to carry out reprocessing correctly upon returning from such an EIT event, it
performs operations before and after the EIT as specified in either case.
(LDI
#value_of_standby, R0)
: value_of_standby is write data to STCR.
(LDI
#_STCR, R12)
: _STCR is address (481H) of STCR.
STB
R0, @R12
: Writing to standby control register (STCR)
LDUB
@R12, R0
: STCR read for synchronous standby
LDUB
@R12, R0
: Dummy re-read of STCR
NOP
: NOP
× 5 for arrangement of timing
NOP
相關PDF資料 |
PDF描述 |
|---|---|
| MB91340PMT | 32-BIT, MROM, 66 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91605PMC | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F158PMC1 | RISC MICROCONTROLLER, PQFP120 |
| MB91F233APFF-GE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F249PFV-GSE1 | 32-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91233LPFF-G-XXX-BNDE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91243PFV-GS-102-BNDE1 | 制造商:FUJITSU 功能描述:ELECTRONIC COMPONENT |
| MB91245 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91245_07 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91245S | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。