- 您現在的位置：買賣IC網 > PDF目錄98010 > MB91233LPFF-G-XXX 32-BIT, MROM, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91233LPFF-G-XXX |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, MROM, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 7/56頁 |
| 文件大?。?/td> | 293K |
| 代理商： | MB91233LPFF-G-XXX |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB91230 Series
15
s
s HANDLING DEVICES
Preventing Latchup
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or output
pin or if an above-rating voltage is applied between VCC and VSS.
A latchup, if it occurs, significantly increases the power supply current and may cause thermal destruction of an
element. When you use a CMOS IC, be very careful not to exceed the maximum rating.
Treatment of Unused Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a pull-
up or pull-down resistor.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
The power pins should be connected to VCC and VSS of this device at the lowest possible impedance from the
current supply source.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS near
this device.
About Crystal Oscillator Circuit
Noise near the X0 and X1 pin may cause the device to malfunction.
Design the circuit board so that X0 and X1, the crystal oscillator (or ceramic oscillator) , and the bypass capacitor
to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1 pins surrounded by ground plane
because stable operation can be expected with such a layout.
Treatment of NC and OPEN pins
Pins marked as NC or OPEN must be left open-circuit.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and VCC or VSS is as short as possible and the connection impedance is low.
Operation at Start-up
Be sure to execute setting initialized reset (INIT) with INIT pin immediately after start-up.
Also, in order to provide a delay while the oscillator circuit stabilize immediately after start-up, maintain the “L”
level input to the INIT pin for the required stabilization wait time. (For INIT via the INIT pin, the oscillation
stabilization wait time setting is initialized to the minimum value) .
相關PDF資料 |
PDF描述 |
|---|---|
| MB91340PMT | 32-BIT, MROM, 66 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91605PMC | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F158PMC1 | RISC MICROCONTROLLER, PQFP120 |
| MB91F233APFF-GE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F249PFV-GSE1 | 32-BIT, FLASH, 32 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91233LPFF-G-XXX-BNDE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91243PFV-GS-102-BNDE1 | 制造商:FUJITSU 功能描述:ELECTRONIC COMPONENT |
| MB91245 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91245_07 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91245S | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。