- 您現在的位置：買賣IC網 > PDF目錄382288 > MB89202P-SH (FUJITSU LTD) 8-Bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB89202P-SH |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit Proprietary Microcontroller |
| 中文描述： | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 1.778 MM PITCH, PLASTIC, DIP-32 |
| 文件頁數： | 17/44頁 |
| 文件大?。?/td> | 427K |
| 代理商： | MB89202P-SH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MB89202 Series
17
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data and
bits for control of CPU operations at the time of an interrupt.
H-flag : Set to “1” when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation.
Cleared to “0” otherwise. This flag is for decimal adjustment instructions.
I-flag :
Interrupt is enabled when this flag is set to “1”. Interrupt is disabled when the flag is cleared to “0”.
Cleared to “0” at the reset.
IL1, 0 :
Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is
higher than the value indicated by this bit.
N-flag : Set to “1” if the MSB becomes to “1” as the result of an arithmetic operation. Cleared to “0” when the
bit is cleared to “0”.
Z-flag : Set to “1” when an arithmetic operation results in 0. Cleared to “0” otherwise.
V-flag : Set to “1” if the complement on 2 overflows as a result of an arithmetic operation. Cleared to “0” if the
overflow does not occur.
C-flag : Set to “1” when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to
“0” otherwise. Set to the shift-out value in the case of a shift instruction.
IL1
IL0
Interrupt level
High-low
0
0
1
High
Low
=
no interrupt
0
1
1
0
2
1
1
3
"0"
"0"
"0"
"0"
"0"
"0"
"0"
"1"
R4
R3
R2
R1
R0
b2
b1
RP
Lower OP codes
b0
A7
A6
A5
A4
A3
A2
A1
A0
A15
Generated addresses
A14 A13 A12 A11 A10
A9
A8
Rule for Conversion of Actual Addresses of the General-purpose Register Area
相關PDF資料 |
PDF描述 |
|---|---|
| MB89202PFV | 8-Bit Proprietary Microcontroller |
| MB89F202 | 8-Bit Proprietary Microcontroller |
| MB89F202P-SH | 8-Bit Proprietary Microcontroller |
| MB89F202PFV | 8-Bit Proprietary Microcontroller |
| MB89V201PFV | 8-Bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89251A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:SERIAL DATA TRANSMITTER / RECEIVER |
| MB89254 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:PROGRAMMABLE TIMER |
| MB89255A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:PARALLEL DATA I/O INTERFACE |
| MB89259A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:INTERRUPT CONTROLLER |
| MB89322B | 制造商:Fuji Electric 功能描述:89322B 制造商:FUJITSU 功能描述:89322B |
發布緊急采購，3分鐘左右您將得到回復。