- 您現在的位置：買賣IC網 > PDF目錄45178 > MAXQ610J-0000+ (MAXIM INTEGRATED PRODUCTS INC) 16-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, QCC44 PDF資料下載
參數資料
| 型號： | MAXQ610J-0000+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, QCC44 |
| 封裝： | ROHS COMPLIANT, TQFN-44 |
| 文件頁數： | 5/29頁 |
| 文件大?。?/td> | 827K |
| 代理商： | MAXQ610J-0000+ |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MAXQ610
16-Bit Microcontroller with Infrared Module
______________________________________________________________________________________
13
The watchdog timer functions as the source of both the
watchdog-timer timeout and the watchdog-timer reset.
The timeout period can be programmed in a range of
215 to 224 system clock cycles. An interrupt is generat-
ed when the timeout period expires if the interrupt is
enabled. All watchdog-timer resets follow the pro-
grammed interrupt timeouts by 512 system clock
cycles. If the watchdog timer is not restarted for another
full interval in this time period, a system reset occurs
when the reset timeout expires. See Table 2.
IR Carrier Generation and
Modulation Timer
The dedicated IR timer/counter module simplifies low-
speed IR communication. The IR timer implements two
pins (IRTX and IRRX) for supporting IR transmit and
receive, respectively. The IRTX pin has no correspond-
ing port pin designation, so the standard PD, PO, and
PI port control status bits are not present. However, the
IRTX pin output can be manipulated high or low using
the PWCN.IRTXOUT and PWCN.IRTXOE bits when the
IR timer is not enabled (i.e., IREN = 0).
The IR timer is composed of two separate timing enti-
ties: a carrier generator and a carrier modulator. The
carrier generation module uses the 16-bit IR Carrier
register (IRCA) to define the high and low time of the
carrier through the IR carrier high byte (IRCAH) and IR
carrier low byte (IRCAL). The carrier modulator uses the
IR data bit (IRDATA) and IR Modulator Time register
(IRMT) to determine whether the carrier or the idle con-
dition is present on IRTX.
The IR timer is enabled when the IR enable bit (IREN) is
set to 1. The IR Value register (IRV) defines the begin-
ning value for the carrier modulator. During transmis-
sion, the IRV register is initially loaded with the IRMT
value and begins down counting towards 0000h,
whereas in receive mode it counts upward from the ini-
tial IRV register value. During the receive operation, the
IRV register can be configured to reload with 0000h
when capture occurs on detection of selected edges or
can be allowed to continue free-running throughout the
receive operation. An overflow occurs when the IR timer
value rolls over from 0FFFFh to 0000h. The IR overflow
flag (IROV) is set to 1 and an interrupt is generated if
enabled (IRIE = 1).
Carrier Generation Module
The IRCAH byte defines the carrier high time in terms of
the number of IR input clocks, whereas the IRCAL byte
defines the carrier low time.
IR Input Clock (fIRCLK) = fSYS/2IRDIV[1:0]
Carrier Frequency (fCARRIER) =
fIRCLK/(IRCAH + IRCAL + 2)
Carrier High Time = IRCAH + 1
Carrier Low Time = IRCAL + 1
Carrier Duty Cycle = (IRCAH + 1)/(IRCAH + IRCAL + 2)
During transmission, the IRCA register is latched for
each IRV downcount interval and is sampled along with
the IRTXPOL and IRDATA bits at the beginning of each
new IRV downcount interval so that duty-cycle variation
and frequency shifting is possible from one interval to
the next, which is illustrated in Figure 1.
Figure 2 illustrates the basic carrier generation and its
path to the IRTX output pin. The IR transmit polarity bit
(IRTXPOL) defines the starting/idle state and the carrier
polarity of the IRTX pin when the IR timer is enabled.
IR Transmission
During IR transmission (IRMODE = 1), the carrier gener-
ator creates the appropriate carrier waveform, while the
carrier modulator performs the modulation. The carrier
modulation can be performed as a function of carrier
cycles or IRCLK cycles dependent on the setting of the
IRCFME bit. When IRCFME = 0, the IRV downcounter is
clocked by the carrier frequency and thus the modula-
tion is a function of carrier cycles. When IRCFME = 1,
the IRV downcounter is clocked by IRCLK, allowing car-
rier modulation timing with IRCLK resolution.
WD[1:0]
WATCHDOG CLOCK
WATCHDOG INTERRUPT TIMEOUT
WATCHDOG RESET AFTER
WATCHDOG INTERRUPT (μs)
00
Sysclk/215
2.7ms
42.7
01
Sysclk/218
21.9ms
42.7
10
Sysclk/221
174.7ms
42.7
11
Sysclk/224
1.4s
42.7
Table 2. Watchdog Interrupt Timeout (Sysclk = 12MHz, CD[1:0] = 00)
相關PDF資料 |
PDF描述 |
|---|---|
| MAXQ613J-0000+ | 16-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, QCC44 |
| MAXQ613A-0000+ | 16-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, QCC32 |
| MAXQ618J-0000+ | 16-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, QCC44 |
| MAZD02400L | 2.4 V, 0.12 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MAZD03000L | 3 V, 0.12 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAXQ610J-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ610J-0000+T | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ610J-UEI+ | 制造商:Maxim Integrated Products 功能描述:MAXQ610 BLANK 44 TQFN UEI - Rail/Tube |
| MAXQ610K-0000+ | 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Microcontrollers - IC MCU 16BIT 64K IR MOD 44TQFP RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ610-KIT# | 功能描述:開發板和工具包 - 其他處理器 MAXQ610 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。