- 您現在的位置：買賣IC網 > PDF目錄2091 > MAX9729ETI+T (Maxim Integrated Products)IC AMP AUDIO .052W STER 28TQFN PDF資料下載
參數資料
| 型號： | MAX9729ETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO .052W STER 28TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 耳機，2-通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 52mW x 2 @ 32 歐姆 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 特點： | 帶低音增強模式，消除爆音，I²C，輸入多路復用器，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
BEEP Input
The MAX9729 features a BEEP input with eight different
attenuation settings (see Table 6). The BEEP input is
useful for applications requiring the routing of a system
alert signal to the stereo audio path. The attenuation
value of the BEEP input is set by bits [7:5] in the 0x01
command register (see Tables 2 and 6). The attenua-
tion settings of the BEEP input are independent of the
volume settings stored in register 0x00 (see Table 2).
The BEEP input is enabled when BEEP_EN is connect-
ed to VDD and disabled when driven low. When
BEEP_EN is high, the selected INL_ and INR_ inputs
are disconnected from the signal path and the BEEP
input signal is routed to both headphone outputs after
being attenuated by the value set by bits [7:5] in regis-
ter 0x01. When BEEP_EN is low, the BEEP input is dis-
connected from the signal path and the selected INL_
and INR_ inputs are reconnected.
Input Multiplexer/Mixer
The MAX9729 includes a stereo 3:1 multiplexer/mixer,
allowing selection and mixing of three different stereo
input sources. Bits [6:5] in register 0x00 control the
selection/mixing of the input signal sources (see Tables
2 and 4). When all three stereo inputs are selected (Bits
[6:5] = 11), the stereo signals are summed (mixed)
together and connected to the signal path. The
MAX9729 implements the automatic volume ramping
function when an input source change occurs to ensure
smooth sounding transitions. Clipping may occur if
three high level signals are summed. Reprogram the
preamplifier maximum gain setting to compensate.
Serial Interface
The MAX9729 features an I2C/SMBus-compatible 2-wire
serial interface consisting of a serial data line (SDA) and
a serial clock line (SCL). SDA and SCL facilitate bidirec-
tional communication between the MAX9729 and the
master at clock rates up to 400kHz. Figure 3 shows the
2-wire interface timing diagram. The MAX9729 is a
transmit/receive slave-only device, relying upon a mas-
ter device to generate the clock signal. The master
device, typically a microcontroller, initiates data transfer
on the bus and generates SCL to permit that transfer.
A master device communicates to the MAX9729 by
transmitting the slave address with the Read/
Write
(R/
W) bit followed by the data word. Each transmit
sequence is framed by a START (S) or REPEATED
START (Sr) condition and a STOP (P) condition. Each
word transmitted over the bus is 8 bits long and is
always followed by an acknowledge or not acknowl-
edge clock pulse.
The MAX9729 SDA line operates as both an input and
an open-drain output. A pullup resistor, greater than
500Ω, is required on the SDA bus. The MAX9729 SCL
line operates as an input only. A pullup resistor, greater
than 500Ω, is required on SCL unless the MAX9729 is
operating in a single-master system where the master
device has a push-pull SCL output. Series resistors in
line with SDA and SCL are optional. Series resistors
protect the digital inputs of the MAX9729 from high-
voltage spikes on the bus lines, and minimize crosstalk
and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse since changes in SDA while SCL is
high are control signals (see the
START and STOP
Conditions section). SDA and SCL idle high when the
I2C bus is not busy.
MAX9729
Stereo Headphone Amplifier with BassMax,
Volume Control, and Input Mux
______________________________________________________________________________________
13
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD, STA
tSU, STA
tHD, STA
tSP
tBUF
tSU, STO
tLOW
tSU, DAT
tHD, DAT
tHIGH
tR
tF
Figure 3. 2-Wire Serial-Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9730ETI+T | IC AMP AUDIO PWR 2.4W G 28TQFN |
| MAX9736AETJ/V+ | IC AMP MONO/STER CLASS D 32TQFN |
| MAX9737ETG+T | IC AMP AUDIO 13W MONO D 24TQFN |
| MAX9738EWP+TG45 | IC AMP AUDIO PWR MONO G 20WLP |
| MAX973ESA+ | IC COMPARATOR OD 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9729EVCMAXQU+ | 功能描述:音頻放大器 Evaluation Kit/Evaluation System for the MAX9729 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9729EVKIT+ | 功能描述:音頻放大器 Evaluation Kit/Evaluation System for the MAX9729 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX972C/D | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX972CPA | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX972CPA+ | 功能描述:校驗器 IC Dual Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。