- 您現在的位置：買賣IC網 > PDF目錄10579 > MAX9597CTI+T (Maxim Integrated Products)IC AUD/VID INTERACE 28TQFN-EP PDF資料下載
參數資料
| 型號： | MAX9597CTI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/32頁 |
| 文件大小： | 0K |
| 描述： | IC AUD/VID INTERACE 28TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 音頻/視頻接口 |
| 應用： | DVD，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
MAX9597
Low-Power Audio/Video Interface
for Single SCART Connectors
______________________________________________________________________________________
13
The full-scale output of the independent operational
amplifiers is 0.5VRMS. The closed-loop gain of the oper-
ational amplifier circuit should be designed such that
the resulting full-scale output is 0.5VRMS. The fixed,
gain-of-4 amplifiers that follow the independent opera-
tional amplifiers amplify the 0.5VRMS to 2VRMS, which
complies with the SCART standard.
An integrated charge pump inverts the +3.3V supply
(VAUD) to create a -3.3V supply (CPVSS), enabling the
audio circuit to operate from bipolar supplies. The
audio signal from the beginning to the end of the signal
path is always biased at ground.
Clickless Muting and Unmuting
The TV audio channel incorporates a zero-crossing
detect (ZCD) circuit that minimizes click noise due to
abrupt signal level changes that occur when entering
or coming out of a mute condition at an arbitrary
moment.
To implement the zero-crossing function when switch-
ing audio signals, set ZCD (register 00h, bit 6) high.
The MAX9597 switches the signal in or out of mute at
the next zero crossing after the mute or unmute request
occurs. See Table 8.
Audio Outputs
The MAX9597 audio output amplifiers feature Maxim’s
DirectDrive architecture, eliminating the need for output-
coupling capacitors required by conventional single-
supply audio line drivers. Conventional single-supply
audio line drivers have their outputs biased about a
nominal DC voltage (typically half the supply) for maxi-
mum dynamic range. Large coupling capacitors are
needed to block this DC bias. Clicks and pops are cre-
ated when the coupling capacitors are charged during
power-up and discharged during power-down.
An internal charge pump inverts the positive supply
(VAUD), creating a negative supply (CPVSS). The audio
output amplifiers operate from the bipolar supplies with
the outputs biased about audio ground (Figure 2). The
benefit of this audio ground bias is that the amplifier
outputs do not have a DC component. The DC-blocking
capacitors required with conventional audio line drivers
are unnecessary, conserving board space, reducing
system cost, and improving frequency response.
The MAX9597 features a low-noise charge pump that
requires only two small ceramic capacitors. The
580kHz switching frequency is well beyond the audio
range and does not interfere with audio signals. The
switch drivers feature a controlled switching speed that
minimizes noise generated by turn-on and turn-off tran-
sients. The di/dt noise caused by the parasitic bond
wire and trace inductance is minimized by limiting the
switching speed of the charge pump.
The SCART standard specifies 2VRMS as the full-scale
for audio signals. As the audio circuits process
0.5VRMS full-scale audio signals internal to the
MAX9597, the gain-of-4 output amplifiers restore the
audio signals to a full scale of 2VRMS.
Video Section
The video circuit routes different video formats between
the set-top box decoder and the TV SCART connector.
It also routes slow-switch and fast-switch control infor-
mation as shown in Figure 3.
Video Inputs
Whether the incoming video input signal is AC-coupled
or DC-coupled into the MAX9597 depends upon the ori-
gin, format, and voltage range of the video signal. Table
1 below shows the recommended connections. Always
AC-couple an external video signal through a 0.1F
capacitor because its voltage range is not well defined
(see the
Typical Application Circuit). For example, the
+VDD
-VDD
GND
VOUT
CONVENTIONAL DRIVER-BIASING SCHEME
DirectDrive BIASING SCHEME
VDD/2
VDD
GND
VOUT
Figure 2. Conventional Driver Output Waveform vs. MAX9597
Output Waveform
相關PDF資料 |
PDF描述 |
|---|---|
| MS3102R22-8P | CONN RCPT 2POS BOX MNT W/PINS |
| MS3102E22-8P | CONN RCPT 2POS BOX MNT W/PINS |
| MS3102E16-9S | CONN RCPT 4POS BOX MNT W/SCKT |
| MAX11506CEE+T | IC FILTER VIDEO HD/SD 16-QSOP |
| SP3243EET-L | IC TXRX RS232 INTELLIGNT 28WSOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9597EVKIT+ | 功能描述:視頻 IC 開發(fā)工具 MAX9597 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Boards 類型:YPbPr to RGBHV Converters 工具用于評估:LMH1251 工作電源電壓:5 V |
| MAX9598CTL+ | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598CTL+T | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598EVKIT+ | 功能描述:交換機 IC 開發(fā)工具 MAX9598 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX9600EUP | 功能描述:校驗器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。