- 您現在的位置：買賣IC網 > PDF目錄383538 > MAX9115EXK-T (MAXIM INTEGRATED PRODUCTS INC) Single LVDS Line Receiver in SC70 PDF資料下載
參數資料
| 型號： | MAX9115EXK-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Single LVDS Line Receiver in SC70 |
| 中文描述： | LINE RECEIVER, PDSO5 |
| 封裝： | SC-70, 5 PIN |
| 文件頁數： | 6/8頁 |
| 文件大小： | 139K |
| 代理商： | MAX9115EXK-T |
M
Detailed Description
LVDS is intended for point-to-point communication over
a controlled-impedance medium as defined by the
ANSI TIA/EIA-644 and IEEE 1596.3 standards. LVDS
uses a lower voltage swing than other common com-
munication standards, achieving higher data rates with
reduced power consumption while reducing EMI emis-
sions and system susceptibility to noise.
The MAX9115 is a single LVDS line receiver ideal for
applications requiring high data rates, low power, and
low noise. The device accepts an LVDS input and
translates it to an LVTTL/LVCMOS output. The receiver
detects differential signals as low as 50mV and as high
as 1V within an input voltage range of 0 to +2.4V.
The 250mV to 450mV differential output of an LVDS dri-
ver is nominally centered around a +1.25V offset. This
offset, coupled with the receiver
’
s 0 to +2.4V input volt-
age range, allows an approximate ±1V shift in the sig-
nal (as seen by the receiver). This allows for a
difference in ground references of the driver and the
receiver, the common-mode effects of coupled noise,
or both. The LVDS standards specify an input voltage
range of 0 to +2.4V referenced to receiver ground.
Fail-Safe
The fail-safe feature of the MAX9115 sets the output
high and reduces supply current when:
inputs are open
inputs are undriven and shorted
inputs are undriven and terminated
A fail-safe circuit is important because under these
conditions, noise at the input may switch the receiver
and it may appear to the system that data is being
received. Open or undriven terminated input conditions
can occur when a cable is disconnected or cut, or
when an LVDS driver output is in high impedance. A
short condition can occur because of a cable failure.
The fail-safe input network (Figure 1) samples the input
common-mode voltage and compares it to V
CC
- 0.3V
(nominal). When the input is driven to levels specified in
the LVDS standards, the input common-mode voltage
is less than V
CC
- 0.3V and the fail-safe circuit is not
activated. If the inputs are open or if the inputs are
undriven and shorted or undriven and parallel terminat-
ed, there is no input current. In this case, a pullup resis-
tor in the fail-safe circuit pulls both inputs above V
CC
-
0.3V, activating the fail-safe circuit and forcing the out-
put high.
Applications Information
Power-Supply Bypassing
Bypass V
CC
with a high-frequency surface-mount
ceramic 0.01μF capacitor in parallel as close to the
device as possible.
Single LVDS Line Receiver in SC70
6
_______________________________________________________________________________________
Pin Description
PIN
NAME
FUNCTION
1
V
CC
Power-Supply Input. Bypass V
CC
to
GND with a 0.01μF ceramic capacitor.
2
3
4
5
GND
IN-
IN+
OUT
Ground
Inverting LVDS Differential Input
Noninverting LVDS Differential Input
LVTTL/LVCMOS Output
IN+
IN-
GND
OUT
MAX9115
V
CC
R
IN2
V
CC
- 0.3V
R
IN1
R
IN1
Figure 1. Input Fail-Safe Network
MAX9115
PULSE
GENERATOR
OUT
*50
REQUIRED FOR PULSE GENERATOR.
IN+
IN-
*50
*50
C
L
Rx
Figure 2. Propagation Delay and Transition Time Test Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9115 | Single LVDS Line Receiver in SC70 |
| MAX9118EXK-T | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9119EXK | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9120EXK-T | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9117 | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9117 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PLASTIC ENCAPSULATED DEVICES |
| MAX9117ESA | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA+ | 功能描述:校驗器 IC SC70 1.6V Nanopower Beyond-the-Rails Comparators With/Without Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA+T | 功能描述:校驗器 IC SC70 1.6V Nanopower Beyond-the-Rails Comparators With/Without Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA-T | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。