- 您現在的位置：買賣IC網 > PDF目錄385553 > MAX882 (Maxim Integrated Products, Inc.) 3.3V or Adjustable, Low-Dropout, Low IQ, 200mA Linear Regulators(3.3V/可調,250mA,具有維持方式,P溝道低壓差線性穩壓器) PDF資料下載
參數資料
| 型號： | MAX882 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3.3V or Adjustable, Low-Dropout, Low IQ, 200mA Linear Regulators(3.3V/可調,250mA,具有維持方式,P溝道低壓差線性穩壓器) |
| 中文描述： | 5V/3.3V或可調、低壓差、低IQ、200mA線性穩壓器，具有待機模式 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 176K |
| 代理商： | MAX882 |
M
5V /3.3V or Adjustable, Low-Dropout,
Low I
Q
, 200mA Linear Regulators
8
_______________________________________________________________________________________
In adjustable mode, the user selects an output voltage
in the 1.25V to 11V range by connecting two external
resistors, used as a voltage divider, to the SET pin
(Figure 2).
The output voltage is set by the following equation:
where V
SET
= 1.20V.
To simplify resistor selection:
Since the input bias current at SET is nominally zero,
large resistance values can be used for R1 and R2 to
minimize power consumption without losing accuracy.
Up to 1.5M
is acceptable for R2. Since the V
SET
toler-
ance is less than ±40mV, the output can be set using
fixed resistors instead of trim pots.
S tandby Mode (MAX 882)
The MAX882 has a standby feature that disconnects
the input from the output when STBY is brought low, but
keeps all other circuitry awake. In this mode, V
OUT
drops to 0V, and the internal biasing circuitry (including
the low-battery comparator) remains on. The maximum
quiescent current during standby is 15μA. STBY is a
comparator input with the other input internally tied to
the reference voltage. Use a resistor network as shown
in Figure 3 to set a standby-mode threshold voltage for
undervoltage lockout. Connect STBY to IN for normal
operation.
OFF Mode (MAX 883/MAX 884)
A low-logic input on the OFF pin shuts down the
MAX883/MAX884. In this mode, the pass transistor,
control circuit, reference, and all biases are turned off,
and the supply current is reduced to less than 1μA.
LBO is undefined in OFF mode. Connect OFF to IN for
normal operation.
R1
R2
V
V
1
OUT
SET
=
V
V
R
R
OUT
SET
=
+
1
1
2
Figure 1. MAX882/MAX883/MAX884 Functional Diagram
P
OUT
SET
R1
R2
65mV
ERROR AMP
OFF
(STBY)
GND
LBO
LBI
N
IN
MOSFET DRIVER
WITH FOLDBACK
CURRENT LIMIT
REVERSE-
CURRENT
PROTECTION
SHUT-
DOWN
LOGIC
1.20V
REFERENCE
THERMAL
SENSOR
( ) ARE FOR MAX882
DUAL-MODE
COMPARATOR
LOW-BATTERY
COMPARATOR
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8862 | Low-Cost, Low-Dropout, Dual Linear Regulator |
| MAX8862_ESE | RES 160K OHM 1/16W 5% 0402 SMD |
| MAX8863T | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8863R | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8863S | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8821ETI+ | 功能描述:LED照明驅動器 White LED Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8821ETI+T | 功能描述:LED照明驅動器 White LED Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8821EVKIT+ | 功能描述:電源管理IC開發工具 MAX8821 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX8822ETE+ | 功能描述:LED照明驅動器 Negative Charge Pump LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8822ETE+T | 功能描述:LED照明驅動器 Negative Charge Pump LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。