- 您現在的位置：買賣IC網 > PDF目錄385553 > MAX882 (Maxim Integrated Products, Inc.) 3.3V or Adjustable, Low-Dropout, Low IQ, 200mA Linear Regulators(3.3V/可調,250mA,具有維持方式,P溝道低壓差線性穩壓器) PDF資料下載
參數資料
| 型號： | MAX882 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3.3V or Adjustable, Low-Dropout, Low IQ, 200mA Linear Regulators(3.3V/可調,250mA,具有維持方式,P溝道低壓差線性穩壓器) |
| 中文描述： | 5V/3.3V或可調、低壓差、低IQ、200mA線性穩壓器，具有待機模式 |
| 文件頁數： | 7/16頁 |
| 文件大小： | 176K |
| 代理商： | MAX882 |
M
5V /3.3V or Adjustable, Low-Dropout,
Low I
Q
, 200mA Linear Regulators
_______________________________________________________________________________________
7
_______________Detailed Desc ription
The MAX882/MAX883/MAX884 are micropower, low-
dropout linear regulators designed primarily for battery-
powered applications. They feature Dual-Mode
operation, allowing a fixed output of 5V for the MAX883
and 3.3V for the MAX882/MAX884, or an adjustable output
from 1.25V to 11V. These devices supply up to 200mA
while requiring less than 15μA quiescent current. As illus-
trated in Figure 1, they consist of a 1.20V reference, error
amplifier, MOSFET driver, P-channel pass transistor, dual-
mode comparator and feedback voltage divider.
The 1.20V reference is connected to the error amplifier’s
inverting input. The error amplifier compares this refer-
ence with the selected feedback voltage and amplifies
the difference. The MOSFET driver reads the error signal
and applies the appropriate drive to the P-channel pass
transistor. If the feedback voltage is lower than the refer-
ence, the pass transistor’s gate is pulled lower, allowing
more current to pass and increasing the output voltage. If
the feedback voltage is too high, the pass transistor gate
is pulled up, allowing less current to pass to the output.
The output voltage is fed back through either an inter-
nal resistor voltage divider connected to the OUT pin,
or an external resistor network connected to the SET
pin. The dual-mode comparator examines the SET pin
voltage and selects the feedback path used. If the SET
pin is below 65mV, internal feedback is used and the
output voltage is regulated to 5V for the MAX883 or
3.3V for the MAX882/MAX884. Additional blocks
include a foldback current limiter, reverse-current pro-
tection, a thermal sensor, shutdown or standby logic,
and a low-battery-detection comparator.
Internal P-Channel Pass T ransistor
The MAX882/MAX883/MAX884 feature a 200mA P-
channel MOSFET pass transistor. This provides several
advantages over similar designs using PNP pass tran-
sistors, including longer battery life.
The P-channel MOSFET requires no base drive, which
reduces quiescent current considerably. PNP based reg-
ulators waste large amounts of current in dropout when
the pass transistor saturates. They also use high base-
drive currents under large loads. The MAX882/MAX883/
MAX884 do not suffer from these problems and consume
only 11μA of quiescent current during light loads, heavy
loads, and dropout.
Output V oltage S elec tion
The MAX882/MAX883/MAX884 feature Dual Mode
operation. In preset voltage mode, the MAX883’s out-
put is set to 5V and the MAX882/MAX884’s output is set
to 3.3V, using internal trimmed feedback resistors.
Select this mode by connecting SET to ground.
In preset voltage mode, impedances between SET and
ground should be less than 100k
. Otherwise, spurious
conditions could cause the voltage at SET to exceed
the 65mV dual-mode threshold.
______________________________________________________________Pin Desc ription
LBO
SET
GND
OUT
LBI
OFF
STBY
IN
1
1
Low-Battery Output is an open-drain output that goes low when LBI is less than 1.2V. Connect to
IN or OUT through a pull-up resistor. LBO is undefined during shutdown mode
(MAX883/MAX884).
Feedback for setting the output voltage. Connect to GND to set the output voltage to the prese-
lected 3.3V or 5V. Connect to an external resistor network for adjustable-output operation.
Ground pins—also function as heatsinks in the SO package. All GND pins must be soldered to
the circuit board for proper power dissipation. Connect to large copper pads or planes to
channel heat from the IC.
Regulator Output. Fixed or adjustable from 1.25V to 11.0V. Sources up to 200mA. Bypass with a
2.2μF capacitor.
Regulator Input. Supply voltage can range from 2.7V to 11.5V.
2
2
3, 6
3, 6
4
4
8
8
Low-Battery comparator Input. Tie to IN when not used.
—
7
Shutdown. Active-low logic input. In OFF mode, supply current is reduced below 1μA and
V
OUT
= 0V
7
—
Standby. Active-low comparator input. Connect to GND to disable the output or to IN for normal
operation. A resistor network (from IN) can be used to set a standby mode threshold.
5
5
NAME
PIN
FUNCTION
MAX883/
MAX884
MAX882
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8862 | Low-Cost, Low-Dropout, Dual Linear Regulator |
| MAX8862_ESE | RES 160K OHM 1/16W 5% 0402 SMD |
| MAX8863T | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8863R | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8863S | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8821ETI+ | 功能描述:LED照明驅動器 White LED Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8821ETI+T | 功能描述:LED照明驅動器 White LED Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8821EVKIT+ | 功能描述:電源管理IC開發工具 MAX8821 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX8822ETE+ | 功能描述:LED照明驅動器 Negative Charge Pump LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX8822ETE+T | 功能描述:LED照明驅動器 Negative Charge Pump LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。