- 您現在的位置：買賣IC網 > PDF目錄383506 > MAX805TMJA (MAXIM INTEGRATED PRODUCTS INC) Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX805TMJA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, CDIP8 |
| 封裝： | 0.300 INCH, CERDIP-8 |
| 文件頁數： | 5/12頁 |
| 文件大小： | 98K |
| 代理商： | MAX805TMJA |
M
Mic roproc essor S upervisory Circ uits
_______________________________________________________________________________________
5
______________________________________________________________Pin Desc ription
PIN
NAME
FUNCTION
MAX805L
1
1
V
OUT
2
2
V
CC
+5V Supply Input
3
3
GND
Ground
4
4
PFI
5
5
PFO
6
6
WDI
7
RESET
8
8
V
BATT
Power-Fail Comparator Input. When PFI is less than 1.25V,
PFO
goes
low. Connect PFI to GND or V
CC
when not used.
Power-Fail Output. When PFI is less than 1.25V,
PFO
goes low;
otherwise
PFO
stays high.
Watchdog Input. If WDI remains high or low for 1.6sec, the internal
watchdog timer runs out and reset is triggered. If WDI is left floating or
connected to a high-impedance three-state buffer, the watchdog
feature is disabled. The internal watchdog timer clears whenever reset
is asserted, WDI is three-stated, or WDI sees a rising or falling edge.
MAX690A/MAX692A
MAX802L/MAX802M
Reset Output. Whenever
RESET
is triggered, it pulses low for 200ms. It
stays low when V
is below the reset threshold (4.65V in the
MAX690A/MAX802L and 4.4V in the MAX692A/MAX802M) and remains
low for 200ms after V
CC
rises above the reset threshold. A watchdog
timeout also triggers
RESET
.
Supply Output for CMOS RAM. When V
is above the reset threshold,
V
connects to V
through a P-channel MOSFET switch. When V
CC
is below the reset threshold, the higher of V
CC
or V
BATT
will be
connected to V
OUT
.
Backup-Battery Input. When V
CC
falls below the reset threshold, V
BATT
will be switched to V
OUT
if V
BATT
is 20mV greater than V
CC
. When V
rises to 20mV above V
, V
will be reconnected to V
CC
. The 40mV
hysteresis prevents repeated switching if V
CC
falls slowly.
–
7
RESET
Active-High Reset Output is the inverse of
RESET
. When RESET is
asserted, the RESET output voltage = V
CC
or V
BATT
, whichever is
higher.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX805RESA | 3.0V/3.3V Microprocessor Supervisory Circuits |
| MAX805RCSA | CANCA02COME36A35SBF80 |
| MAX808LMJA | Interface IC |
| MAX808 | 8-Pin レP Supervisory Circuits with 【1.5eset Accuracy |
| MAX801L-MAX808N | 5015 RR 3#8 SKT RECP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX806 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Microprocessor Supervisory Circuits |
| MAX806_C/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.0V/3.3V Microprocessor Supervisory Circuits |
| MAX806_CPA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.0V/3.3V Microprocessor Supervisory Circuits |
| MAX806_CSA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.0V/3.3V Microprocessor Supervisory Circuits |
| MAX806_EPA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.0V/3.3V Microprocessor Supervisory Circuits |
發布緊急采購，3分鐘左右您將得到回復。