參數資料
型號: MAX7000A
廠商: Altera Corporation
英文描述: Programmable Logic Device
中文描述: 可編程邏輯器件
文件頁數: 16/60頁
文件大?。?/td> 943K
代理商: MAX7000A
16
Altera Corporation
MAX 7000A Programmable Logic Device Data Sheet
In-System
Programma-
bility
MAX 7000A devices can be programmed in-system via an industry-
standard 4-pin IEEE Std. 1149.1 (JTAG) interface. ISP offers quick, efficient
iterations during design development and debugging cycles. The
MAX 7000A architecture internally generates the high programming
voltages required to program EEPROM cells, allowing in-system
programming with only a single 3.3-V power supply. During in-system
programming, the I/O pins are tri-stated and weakly pulled-up to
eliminate board conflicts. The pull-up value is nominally 50 k
.
MAX 7000AE devices have an enhanced ISP algorithm for faster
programming. These devices also offer an ISP_Done bit that provides safe
operation when in-system programming is interrupted. This ISP_Done
bit, which is the last bit programmed, prevents all I/O pins from driving
until the bit is programmed. This feature is only available in EPM7032AE,
EPM7064AE, EPM7128AE, EPM7256AE, and EPM7512AE devices.
ISP simplifies the manufacturing flow by allowing devices to be mounted
on a PCB with standard pick-and-place equipment before they are
programmed. MAX 7000A devices can be programmed by downloading
the information via in-circuit testers, embedded processors, the Altera
MasterBlaster serial/USB communications cable, ByteBlasterMV parallel
port download cable, and BitBlaster serial download cable. Programming
the devices after they are placed on the board eliminates lead damage on
high-pin-count packages (e.g., QFP packages) due to device handling.
MAX 7000A devices can be reprogrammed after a system has already
shipped to the field. For example, product upgrades can be performed in
the field via software or modem.
In-system programming can be accomplished with either an adaptive or
constant algorithm. An adaptive algorithm reads information from the
unit and adapts subsequent programming steps to achieve the fastest
possible programming time for that unit. A constant algorithm uses a pre-
defined (non-adaptive) programming sequence that does not take
advantage of adaptive algorithm programming time improvements.
Some in-circuit testers cannot program using an adaptive algorithm.
Therefore, a constant algorithm must be used. MAX 7000AE devices can
be programmed with either an adaptive or constant (non-adaptive)
algorithm. EPM7128A and EPM7256A device can only be programmed
with an adaptive algorithm; users programming these two devices on
platforms that cannot use an adaptive algorithm should use EPM7128AE
and EPM7256AE devices.
The Jam Standard Test and Programming Language (STAPL), JEDEC
standard JESD 71, can be used to program MAX 7000A devices with in-
circuit testers, PCs, or embedded processors.
相關PDF資料
PDF描述
MAX7000AE Programmable Logic Device
MAX7000B Programmable Logic Device
MAX7000 Programmable Logic Device Family
MAX7000S Programmable Logic Device Family
MAX7030 RES 22.1-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA
相關代理商/技術參數
參數描述
MAX-7000A 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Programmable Logic Device
MAX7000AE 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Programmable Logic Device
MAX7000B 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Programmable Logic Device
MAX7000S 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Programmable Logic Device Family
MAX700C/D 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel