- 您現在的位置：買賣IC網 > PDF目錄224190 > MAX6889ETJ+ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Octal/Hex/Quad, Power-Supply Sequencers/Supervisors PDF資料下載
參數資料
| 型號： | MAX6889ETJ+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | EEPROM-Programmable, Octal/Hex/Quad, Power-Supply Sequencers/Supervisors |
| 中文描述： | 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC32 |
| 封裝： | 5 X 5 MM, TQFN-32 |
| 文件頁數： | 22/40頁 |
| 文件大?。?/td> | 255K |
| 代理商： | MAX6889ETJ+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MAX6889/MAX6890/MAX6891
EEPROM-Programmable, Octal/Hex/Quad,
Power-Supply Sequencers/Supervisors
______________________________________________________________________________________
29
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
BIT
RANGE
DESCRIPTION
[0]
0 = Write is not disabled if PO1 asserts
1 = Write disabled if PO1 asserts
[1]
0 = Write is not disabled if PO2 asserts
1 = Write disabled if PO2 asserts
[2]
0 = Write is not disabled if PO3 asserts
1 = Write disabled if PO3 asserts
[3]
0 = Write is not disabled if PO4 asserts
1 = Write disabled if PO4 asserts
[4]
0 = Write is not disabled if PO5 asserts
1 = Write disabled if PO5 asserts
[5]
0 = Write is not disabled if PO6 asserts
1 = Write disabled if PO6 asserts
[6]
0 = Write is not disabled if PO7 asserts
1 = Write disabled if PO7 asserts
2Ch
ACh
[7]
0 = Write is not disabled if PO8 asserts
1 = Write disabled if PO8 asserts
[0]
0 = Write is not disabled if PO9 asserts
1 = Write disabled if PO9 asserts
[1]
0 = Write is not disabled if PO10 asserts
1 = Write disabled if PO10 asserts
2Dh
ADh
[7:2]
Not used
Table 23. Write Disable Register
Configuring the
MAX6889/MAX6890/MAX6891
The MAX6889/MAX6890/MAX6891 factory-default con-
figuration sets all registers to 0h, except bits in Tables
17 and 18, which are set to 1h. Factory-default configu-
ration sets all PO_’s as active-high, open drain (all out-
puts are high impedance until the device is configured
by the user). Each device requires configuration before
full power is applied to the system. To configure the
MAX6889/MAX6890/MAX6891, first apply an input volt-
age to IN1, or one of IN2–IN5 or VCC (see the Powering
the MAX6889/MAX6890/MAX6891 section). VIN1 > 4V,
or one of VIN2–VIN5 or VCC > 2.7V to ensure device
operation. Next, transmit data through the serial inter-
face. Use the block write protocol to quickly configure
the device. Write to the configuration registers first to
ensure the device is configured properly. After com-
pleting the setup procedure, use the read word or
block read protocol to read back the data from the con-
figuration registers. Lastly, use the write byte or block
write protocol to write this data to the EEPROM regis-
ters. After completing the EEPROM register configura-
tion, apply full power to the system to begin normal
operation. The nonvolatile EEPROM stores the latest
configuration upon removal of power. Write 0s to all
EEPROM registers to clear the memory.
Software Reboot
A software reboot allows the user to restore the EEPROM
configuration to the volatile registers without cycling the
power supplies. Use the send byte command with data
byte C4h to initiate a software reboot. The 3ms (max)
power-up delay also applies after a software reboot.
Configuration EEPROM
The configuration EEPROM addresses range from 80h
to AEh. Write data to the configuration EEPROM to auto-
matically set up the MAX6889/MAX6890/MAX6891 upon
power-up. Data is transferred from the configuration
EEPROM to the configuration registers when VCC
exceeds UVLO during power-up or after a software
相關PDF資料 |
PDF描述 |
|---|---|
| MAX708SMJA/883B | 1-CHANNEL POWER SUPPLY SUPPORT CKT, CDIP8 |
| MAX8867C/D25 | 2.5 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, UUC5 |
| MAYS0750Z | 7.5 V, 0.15 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MB(2)P-90S | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
| MB(2)P-90 | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6889ETJ+ | 功能描述:監控電路 EEPROM-Prog Octal Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6889ETJ+T | 功能描述:監控電路 EEPROM-Prog Octal Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6889ETJ-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6889EVCMAXQ | 功能描述:監控電路 EEPROM-Programmable Octal/Hex/Quad Power-Supply Sequencers/Supervisors RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6889EVCMAXQU | 功能描述:監控電路 Evaluation Kit/Evaluation System for the MAX6889 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。