- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5926EEE+ (Maxim Integrated)IC HOT-SWAP CONTROLLER 16QSOP-EP Datasheet資料下載
參數資料
| 型號： | MAX5926EEE+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 11/21頁 |
| 文件大小： | 333K |
| 描述： | IC HOT-SWAP CONTROLLER 16QSOP-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 1 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-LSSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP 裸露焊盤 |
| 包裝： | 管件 |
1V to 13.2V, n-Channel Hot-Swap Controllers
Require No Sense Resistor
______________________________________________________________________________________ 11
Detailed Description
The MAX5924/MAX5925/MAX5926 are hot-swap con-
troller ICs designed for applications where a line card is
inserted into a live backplane. Normally, when a line card
is plugged into a live backplane, the cards discharged
filter capacitors provide a low impedance that can
momentarily cause the main power supply to collapse.
The MAX5924/MAX5925/MAX5926 are designed to
reside either in the backplane or in the removable card
to provide inrush current limiting and short-circuit pro-
tection. This is achieved using an external n-channel
MOSFET and an optional external current-sense resistor.
Several critical parameters can be configured:
" Slew rate (inrush current)
" Circuit-breaker threshold
" Turn-on voltage
" Fault-management mode (MAX5926)
" Circuit-breaker temperature coefficient (MAX5926)
See the Selector Guide for a device-specific list of fac-
tory-preset features and parameters.
Startup Mode
It is important that both V
CC
and V
S
rise at a minimum
rate of 100mV/ms during the critical time when power
voltages are below those values required for proper
logic control of internal circuitry. This applies for 0.5V d
V
CC
d 2.5V and 0.5V d V
S
d 0.8V. This is particularly
true when LATCH is tied high.
The MAX5924/MAX5925/MAX5926 control an external
MOSFET placed in the positive power-supply pathway.
When power is first applied, the MAX5924/MAX5925/
MAX5926 hold the MOSFET off indefinitely if the supply
voltage is below the undervoltage lockout level or if the
device is disabled (see the EN (MAX5924/MAX5925),
EN1/EN2 (MAX5926) section). If neither of these condi-
tions exist, the device enters a UVLO startup delay
period for H200ms. Next, the MAX5924/MAX5925/
MAX5926 detect whether an external sense resistor is
present; and then autoconfigure accordingly (see
Figure 4).
" If no sense resistor is present, bilevel fault protection
is disabled and load-probing circuitry is enabled
(see the Load Probing section).
If load probing is not successful, the fault is man-
aged according to the selected fault management
mode (see the Latched and Auto-Retry Fault
Management section).
If load probing (see the Load Probing section) is suc-
cessful, slew-rate limiting is employed to gradually
turn on the MOSFET.
" If the device detects an external R
SENSE
, circuit-
breaker threshold is set at 2xI
CB
, the slow compara-
tor is disabled, the startup phase begins without
delay for load probing, and slew-rate limiting is
employed to gradually turn on the MOSFET.
During the startup phase, the voltage at the load, V
OUT
,
rises at a rate determined by the selected slew rate (see
the Slew Rate section). The inrush current, I
INRUSH
, to
the load is limited to a level proportional to the load
capacitance, C
L
, and the slew rate:
where SR is the slew rate in V/ms and C
L
is load capac-
itance in 礔.
For operation with and without R
SENSE
, once V
GATE
-
V
OUT
exceeds V
CB,EN
, PGOOD and/or PGOOD
assert. When V
GATE
- V
OUT
= V
CB,EN
, the MAX5924/
MAX5925/MAX5926 enable standard bilevel fault pro-
tection with normal I
CB
(see the Bilevel Fault Protection
section).
I
C SR
INRUSH
L
=
?/DIV>
1000
V
CC
RISES ABOVE V
UVLO
ENABLE TRUE?
UVLO 200ms DELAY
V
GS
e V
THPGOOD
FAULT MANAGEMENT
DISABLE FAULT PROTECTION,
ENABLE LOAD PROBE
SLEW-RATE-LIMITED
STARTUP
RSENSE
PRESENT?
VGS e VCB,EN
NO
NO
NO
PGOOD
YES
NO
YES
YES
YES
LOAD PROBE
SUCCESSFUL?
ENABLE STANDARD BILEVEL
FAULT PROTECTION
BEGIN NORMAL OPERATION
I
CB,SU
= 2 x I
CB
DISABLE SLOW
COMPARATOR
Figure 4. Startup Flow Chart
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5929BEEG+ | IC HOT SWAP CTLR QUAD 24QSOP |
| MAX5930AEEG+ | IC HOT SWAP CTLR PWR SEQ 24QSOP |
| MAX5932ESA+T | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5933EESA+ | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5934EEE+ | IC HOT-SWAP CONTROLLER 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5926EEE+ | 功能描述:熱插拔功率分布 1-13.2V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5926EEE+T | 功能描述:熱插拔功率分布 1-13.2V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5926EEE-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5926EVKIT | 制造商:Maxim Integrated Products 功能描述:1V TO 13.2V N-CHANNEL HOT-SWAP CON - Rail/Tube |
| MAX5927AETJ+ | 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。