- 您現在的位置：買賣IC網 > PDF目錄9404 > MAX5418LETA+T (Maxim Integrated Products)IC POT DGTL 256-TAP I2C 8-TDFN PDF資料下載
參數資料
| 型號： | MAX5418LETA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 256-TAP I2C 8-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN-EP（3x3） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1399 (CN2011-ZH PDF) |
| 其它名稱： | MAX5418LETA+TDKR |
MAX5417/MAX5418/MAX5419
256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________
9
Analog Circuitry
The MAX5417/MAX5418/MAX5419 consist of a resistor
array with 255 resistive elements; 256 tap points are
accessible to the wiper, W, along the resistor string
between H and L. The wiper tap point is selected by
programming the potentiometer through the 2-wire (I2C)
interface. Eight data bits, an address byte, and a con-
trol byte program the wiper position. The H and L termi-
nals of the MAX5417/MAX5418/MAX5419 are similar to
the two end terminals of a mechanical potentiometer.
The MAX5417/MAX5418/MAX5419 feature power-on
reset circuitry that loads the wiper position from non-
volatile memory at power-up.
Digital Interface
The MAX5417/MAX5418/MAX5419 feature an internal,
nonvolatile EEPROM that stores the wiper state for ini-
tialization during power-up. The shift register decodes
the control and address bits, routing the data to the
proper memory registers. Data can be written to a
volatile memory register, immediately updating the
wiper position, or data can be written to a nonvolatile
register for storage.
The volatile register retains data as long as the device
is powered. Once power is removed, the volatile regis-
ter is cleared. The nonvolatile register retains data even
after power is removed. Upon power-up, the power-on
reset circuitry controls the transfer of data from the non-
volatile register to the volatile register.
Serial Addressing
The MAX5417/MAX5418/MAX5419 operate as a slave
that receives data through an I2C- and SMBus-com-
patible 2-wire interface. The interface uses a serial data
access (SDA) line and a serial clock line (SCL) to
achieve communication between master(s) and
slave(s). A master, typically a microcontroller, initiates
all data transfers to the MAX5417/MAX5418/MAX5419,
and generates the SCL clock that synchronizes the
data transfer (Figure 1).
The MAX5417/MAX5418/MAX5419 SDA line operates
as both an input and an open-drain output. A pullup
resistor, typically 4.7k
, is required on the SDA bus.
The MAX5417/MAX5418/MAX5419 SCL operates only
as an input. A pullup resistor, typically 4.7k
, is
required on the SCL bus if there are multiple masters
on the 2-wire interface, or if the master in a single-mas-
ter system has an open-drain SCL output.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the
MAX5417/MAX5418/MAX5419 7-bit slave address plus
the 8th bit (Figure 4), 1 command byte (Figure 7) and 1
data byte, and finally a STOP (P) condition (Figure 3).
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START condition by transitioning SDA from
high to low while SCL is high. When the master has fin-
ished communicating with the slave, it issues a STOP
condition by transitioning the SDA from low to high
while SCL is high. The bus is then free for another
transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable while SCL
is high (Figure 5).
SDA
START
CONDITION
SCL
S
STOP
CONDITION
P
Figure 3. Start and Stop Conditions
SDA
SCL
*See the Ordering Information/Selector Guide section for other address options.
01
A0
MSB
LSB
NOP/W
ACK
0
1
0*
Figure 4. Slave Address
SMBus is a trademark of Intel Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27466T23A35S | CONN RCPT 100POS WALL MNT W/SCKT |
| MS27466E23A35S | CONN RCPT 100POS WALL MNT W/SCKT |
| MS27474E8A98PA | CONN RCPT 3POS JAM NUT W/PINS |
| DS1670E+ | IC CTRLR SYSTEM PORTABLE 20TSSOP |
| DS12C887+ | IC RTC W/RAM 128 BYTE 24-EDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5418META | 制造商:Maxim Integrated Products 功能描述:MAXIM MAX5418META, DIGITAL POTENTIOMETERS - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:Maxim MAX5418META, 100Kohm Digital Potentiometer 256-Tap 2.7V-5.25V 8-pin TDFN |
| MAX5418META+ | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 256POS 100KOHM SGL 8TDFN EP - Rail/Tube |
| MAX5418META+T | 功能描述:數字電位計 IC 256-Tap Nonvolatile I2C-Interface RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5418META-T | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5418NETA | 制造商:Maxim Integrated Products 功能描述:256-TAP NONVOLATILE 2-WIRE INTERF - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。