參數資料
型號: MAX5406ETM
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 數字電位計
英文描述: Audio Processor with Pushbutton Interface
中文描述: 10K DIGITAL POTENTIOMETER, PUSH-BUTTON CONTROL INTERFACE, QCC48
封裝: 7 X 7 MM, 0.80 MM HEIGHT, TQFN-48
文件頁數: 15/26頁
文件大?。?/td> 516K
代理商: MAX5406ETM
M
Audio Processor with Pushbutton Interface
______________________________________________________________________________________
15
Up/Down Interface
The MAX5406 features independent control inputs for
volume, balance, ambience, and tone control. All con-
trol inputs are internally debounced for use with
momentary contact SPST switches. All switch inputs
are pulled up to V
LOGIC
through 50k
Ω
resistors. The
wiper setting advances once per button press held for
up to 1s (see Figures 2a and 2b). Maxim’s SmartWiper
control circuitry allows the wiper to advance at a rate of
4Hz when an input is held low from 1s up to 4s, and at
a rate of 16Hz if the contact is maintained for greater
than 4s without the need of a μP (see Figure 3 and
Table 1). The MAX5406 ignores multiple buttons being
pressed. A μP can also be used to control the
MAX5406.
Volume Control
The MAX5406 implements dual logarithmic potentiome-
ters for volume control that change the sound level by
2dB per button push (see Table 2).
In volume-control mode, the MAX5406’s wipers move
up and down together (see Figure 4). The balance is
unaffected (see the
Balance Control
section). Left and
right balance settings are maintained when adjusting
the volume.
Balance Control
In balance-control mode, the MAX5406 uses dual
potentiometers to control balance for the left and right
channels. Pressing
BALR
increases the right channel
wiper by 1dB and decreases the left channel by 1dB.
This causes the right channel to sound louder than the
left channel by 2dB. The overall volume remains con-
stant when adjusting the balance (Figure 5).
Volume and Balance Interaction
Volume and balance operation is simple. However,
there are some interactions that occur at the extreme
wiper positions. These interactions are described in this
section of the data sheet.
When the volume setting is at the maximum level, the
first command to move the balance toward the left chan-
nel forces the right channel to decrease by 1dB.
Subsequent pressing of
BALL
causes the right channel
to decrease by 2dB. At this position, shown in the right
column of Figure 6a, the left-channel volume is maxi-
mum, but the actual separation between L and R is 3dB.
At this position, pressing
VOLDN
restores the actual
balance setting only after
VOLDN
is pressed at least
half as many times as
BALL
was (previously) pressed
(shown in the middle and right column of Figure 6b) to
increase the right-channel balance.
The volume and balance interaction is similar when vol-
ume setting is at the minimum level.
Tone Control
The MAX5406 implements a linear potentiometer to
control the bass and treble over a range of ±10dB
using the recommended component values.
Note that the actual response achieved is determined
by the values of both external and internal components
and the design equations are somewhat interactive.
Use the values shown in the
Electrical Characteristics
as a good starting point for choosing component val-
ues. These components yield shelf turnovers at 100Hz
(bass) and 10kHz (treble) with a total ±10dB of boost at
100Hz and 10kHz. The shoulder or flat portion of the
response is centered on 1kHz.
The circuit in Figure 7 shows the internal structure of
the tone-control system should modification to the
CONTACT
DURATION
WIPER ACTION
t < t
LPW
No motion (debouncing) (Figures 2a and 2b)
t
LPW
t
1s
Wiper changes position once (Figures 2a
and 2b)
1s
t < 4s
Wiper changes position at a rate of 4Hz
(Figure 3)
t
4s
Wiper changes position at a rate of 16Hz
(Figure 3)
Table 1. Wiper Action vs. Pushbutton
Contact Duration
POSITION
0
1
2
…..
10 ( Power-on state)
…..
30
31
32 (Mute)
ATTENUATION (dB)
0
2
4
…..
20
…..
60
62
> 90
Table 2. Attenuator Position For Volume
Potentiometers
相關PDF資料
PDF描述
MAX5406EUM Audio Processor with Pushbutton Interface
MAX5422 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers
MAX5422ETA 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers
MAX5423ETA 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers
MAX5424ETA 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers
相關代理商/技術參數
參數描述
MAX5406EUM+ 功能描述:數字電位計 IC Audio Processor w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MAX5406EUM+T 功能描述:數字電位計 IC Audio Processor w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MAX5407EKA 制造商:Maxim Integrated Products 功能描述:32-TAP AUDIO LOGARITHMIC TAPER DIGI - Rail/Tube
MAX5407EKA+ 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 20KOHM SGL 8PIN SOT-23 - Rail/Tube
MAX5407EKA+T 功能描述:數字電位計 IC 32-Tap Audio Log Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel