- 您現在的位置：買賣IC網 > PDF目錄385527 > MAX3766 (Maxim Integrated Products, Inc.) Quad LVDS Transmitter with Flow-Through Pinout 16-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MAX3766 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Quad LVDS Transmitter with Flow-Through Pinout 16-TSSOP -40 to 85 |
| 中文描述： | 622Mbps、LAN/WAN激光驅動器，帶有自動功率控制及安全關斷 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 250K |
| 代理商： | MAX3766 |
M
622Mbps LAN/WAN Laser Driver with
Automatic Power Control and S afety S hutdown
14
______________________________________________________________________________________
Table 3. MAX3766 Fault Response in Latched Shutdown Configuration
High voltage on REF1 causes a failure and latched
shutdown.
REF1
Normal condition for circuit operation.
ENABLE
Modulation current is increased. Either the APC
circuit will reduce power levels, or an overcurrent
will be detected at MD, causing a failure signal
and latched shutdown.
REF2, TC, MOD
Normal condition for circuit operation.
SAFETY
Normal condition for circuit operation.
OUT-
No effect on circuit.
FAIL
Forces output to either constant 1 or 0. APC main-
tains the power level at the programmed level.
IN+, IN-
PIN
Depending upon the setting of R
POWERSET
,
there is either no effect, or a latched shutdown.
BIASMAX
CIRCUIT RESPONSE TO OVERVOLTAGE
OR SHORT TO V
CC
Modulation and bias currents are reduced or off;
no hazard exists.
Modulation and bias currents are shut down.
Modulation current is reduced; no hazard exists.
Safety shutdown features are disabled, but a
hazard is not created.
Forces output to be logic 1. APC maintains the
power level at the programmed level.
No effect on circuit.
Forces output to either constant 1 or 0. APC main-
tains the power level at the programmed level.
Bias current reduction causes a low laser output,
resulting in a latched shutdown.
CIRCUIT RESPONSE TO UNDERVOLTAGE
OR SHORT TO GROUND
Voltage increase at these pins will turn off the
laser.
OUT+, BIAS
High laser output asserts
FAIL
. A complete short
will destroy the laser, eliminating the hazard. A
resistive short may cause a hazard. External
circuitry combined with the
FAIL
signal may be
used to protect against a resistive short (Figure 10).
Laser output increases, but is limited by the setting
of R
BIASMAX
.
POWERSET
Laser output decreases.
Voltage increase at MD causes a failure and output
current shutdown.
MD
Voltage decrease at MD causes a failure and
output current shutdown.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3770CEE | 2.125Gbps/1.063Gbps, 3.3V Fibre Channel Repeaters |
| MAX3770 | DIODE SCHOTTKY TRIPLE ISOLATED 30V 200mW 0.38V-vf 200mA-IFM 1mA-IF 0.2uA-IR SOT-363 3K/REEL |
| MAX3773 | Dual-Rate Fibre Channel Repeaters |
| MAX3774 | Dual-Rate Fibre Channel Repeaters |
| MAX3775 | Dual-Rate Fibre Channel Repeaters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3766E/D | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3766E/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX3766EEP | 功能描述:激光驅動器 622Mbps LAN/WAN RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3766EEP+ | 功能描述:激光驅動器 622Mbps LAN/WAN RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3766EEP+T | 功能描述:激光驅動器 622Mbps LAN/WAN RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。