- 您現在的位置：買賣IC網 > PDF目錄384665 > MAX3669 (Maxim Integrated Products, Inc.) Single LVDS Transmitter 8-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | MAX3669 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Single LVDS Transmitter 8-SOIC -40 to 85 |
| 中文描述： | +3.3V、622Mbps、 SDH/SONET激光驅動器，帶有電流監測和自動功率控制 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 758K |
| 代理商： | MAX3669 |
M
+3.3V, 622Mbps SDH/SONET
Laser Driver with Current Monitors and APC
6
_______________________________________________________________________________________
NAME
FUNCTION
1, 2, 6, 15,
17, 20, 24
3
4
5, 10, 14, 21,
22, 30
7
8
V
CC
Positive Supply Voltage
29
APCSET
APC Set Resistor. A resistor connected from this pad to ground sets the desired average opti-
cal power. The resulting current is equal to the desired DC monitor diode current. Connect a
100k
resistor from this pad to ground if APC is not used.
Modulation Set Resistor. A resistor from this pad to ground sets the laser modulation current.
PIN
DATA+
DATA-
Positive PECL Data Input
Negative PECL Data Input
32
BIASMAX
Maximum Bias Set Resistor. A resistor from this pad to ground sets the maximum laser bias
current. The APC function can subtract from this maximum value but cannot add to it. This
resistor controls the bias-current level when the APC loop is not used.
31
MODSET
GND
Ground
12, 13, 26,
27, 28
16
N.C.
No Connection. Leave unconnected.
11
FAIL
TTL Output. Indicates APC failure when low. Internally pulled high through a 6k
resistor.
9
ENABLE
TTL/CMOS Enable Input. High for normal operation, low to disable laser bias and modulation
currents. Internally pulled high.
BIAS
Laser Bias Current Output. Isolate from laser with a ferrite bead.
Positive Modulation Current Output. I
MOD
flows into this pad when the input signal is high.
Connect this pad to AC-coupling network.
19
OUT-
Negative Modulation Current Output. I
MOD
flows into this pad when the input signal is low.
Connect this pad to V
CC
through a 6.3
resistor.
Monitor Photodiode Connection. Connect this pad to the monitor photodiode anode. A capaci-
tor to ground is required to filter high-speed AC monitor photocurrent.
18
OUT+
23
MD
25
CAPC
APC Compensation Capacitor. A 0.1μF capacitor connected from this pad to ground controls
the dominant pole of the APC feedback loop.
Pin Description
BIASMON
MODMON
Sink Current Source—proportional to the laser bias current.
Sink Current Source—proportional to the laser modulation current.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3669EHJ | +3.3V, 622Mbps SDH/SONET Laser Driver with Current Monitors and APC |
| MAX3672 | Low-Jitter 155MHz/622MHz Clock Generator |
| MAX3675EHJ | 622Mbps, Low-Power, 3.3V Clock-Recovery and Data-Retiming IC with Limiting Amplifier |
| MAX3675 | 622Mbps, Low-Power, 3.3V Clock-Recovery and Data-Retiming IC with Limiting Amplifier |
| MAX3675ECJ | 622Mbps, Low-Power, 3.3V Clock-Recovery and Data-Retiming IC with Limiting Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3669E/D | 功能描述:激光驅動器 DICE SALES DICE12 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3669E/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX3669E/D+ | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3669EHJ | 功能描述:激光驅動器 3.3V 622Mbps SDH/SONET RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3669EHJ+ | 功能描述:激光驅動器 3.3V 622Mbps SDH/SONET RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。