- 您現在的位置：買賣IC網 > PDF目錄1939 > MAX3302EETI+ (Maxim Integrated Products)IC USB TXRX OTG 28-TQFN-EP PDF資料下載
參數資料
| 型號： | MAX3302EETI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB TXRX OTG 28-TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 類型： | 收發器 |
| 規程： | USB 2.0 |
| 電源電壓： | 3 V ~ 4.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
24
______________________________________________________________________________________
SET COMMAND (ADDRESS 06h)
BEHAVIOR OF MAX3301E/MAX3302E
vbus_drv
vbus_dischrg
vbus_chrg
vbus_drv
vbus_dischrg
vbus_chrg
1X
X
1
0
01X
0
1
0
00
1
0
1
0
Not affected
Table 9. VBUS Control Logic
BIT NUMBER
SYMBOL
CONTENTS
0
vbus_vld
Logic 1 if VBUS > VBUS valid comparator threshold.
1
sess_vld
Logic 1 if VBUS > session valid comparator threshold.
2
dp_hi
Logic 1 if VD+ > dp_hi comparator threshold (D+ assertion during data line pulsing through
SRP method).
3
id_gnd
Logic 1 if VID_IN < 0.1 x VCC.
4
dm_hi
Logic 1 if VD- > dm_hi comparator threshold (D- assertion during data line pulsing through SRP
method).
5
id_float
Logic 1 if VID_IN > 0.9 x VCC.
6
bdis_acon
Logic 1 if bdis_acon_en = 1 and the MAX3301E/MAX3302E assert dp_pullup after detecting a
B device disconnect during HNP.
7
cr_int_sess_end
Logic 1 if VBUS < sess_end comparator threshold, or if VD+ > cr_int comparator threshold (0.4V to
0.6V), depending on the value of int_source (bit 5 of special-function register 1, see Table 14).
Table 10. Interrupt Source Register (Address 08h is Read Only)
Interrupt Registers
Four registers control all interrupt behavior of the
MAX3301E/MAX3302E. A source register (Table 10)
indicates the current status of the various interrupt
sources. An interrupt latch register (Table 11) indicates
which interrupts have occurred. An interrupt-enable low
and interrupt-enable high register enable interrupts on
rising or falling (or both) transitions. Tables 10–13 pro-
vide the bit configurations for the various interrupt regis-
ters. The interrupt latch, interrupt-enable low, and
interrupt-enable high registers have two addresses that
implement write- one-set and write-one-clear features for
each of these registers. Writing a 1 to the set address
sets that bit to 1. Writing a 1 to the clear address resets
that bit to 0. Writing a 0 to either address has no effect
on the bits.
Special-Function Registers
Tables 14, 15, and 16 describe the special-function
registers. The special-function registers have two
addresses that implement write-one-set and write-one-
clear features for each of these registers. Writing a 1 to
the set address sets that bit to 1. Writing a 1 to the clear
address resets that bit to 0. Writing a 0 to either
address has no effect on the bits. Special-function reg-
ister 1 determines whether hardware or software con-
trols the maximum data rate and suspend behavior,
sets the direction of data transfer, and toggles general-
purpose buffer mode. Special-function register 2
enables shutdown mode, configures the interrupt out-
put as open-drain or push-pull, sets the TRM power
source, and controls the D+/D- connections for audio
mode. Table 15 depicts the special-function register 2
for the MAX3301E and Table 16 depicts the special-
function register 2 for the MAX3302E.
The MAX3301E powers up in its lowest power state and
must be turned on by setting the sdwn bit to 0. The
MAX3302E powers up in the operational, VP/VM USB
mode. This allows a P to use the USB port for power-
on boot-up, without having to access I2C. To put the
MAX3302E into low-power shutdown, set the
sdwn bit
to 0. The MAX3302E also has special-function register
2 mapped to two I2C register addresses. In the
MAX3302E, special-function register 2 can be
X = Don’t care.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3311EEUB | IC TXRX RS232 460KBPS 10-UMAX |
| MAX3313EUB | IC TXRX RS232 460KBPS 10-UMAX |
| MAX3314EESA+ | IC TXRX RS232 460KBPS 8-SOIC |
| MAX3314EUA+T | IC TXRX RS232 460KBPS 8-UMAX |
| MAX3317EEAP+ | IC TXRX RS232 460KBPS 20-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3302EETI+ | 功能描述:USB 接口集成電路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX3302EETI+T | 功能描述:USB 接口集成電路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX3302EETJ+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+T | 功能描述:USB 接口集成電路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。