- 您現在的位置：買賣IC網 > PDF目錄8621 > MAX2078CTK+ (Maxim Integrated Products)IC FRNT-END ULTRASOUND 8CH 68QFN PDF資料下載
參數資料
| 型號： | MAX2078CTK+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRNT-END ULTRASOUND 8CH 68QFN |
| 應用說明： | Ultrasound Imaging Systems Application Note |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 特色產品： | MAX2078 Octal-Channel Ultrasound Front-End with CW Doppler Mixers |
| 標準包裝： | 30 |
| 類型： | 超聲波接收器 |
| 應用： | 醫療用超聲波成像，聲納 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-TQFN 裸露焊盤 |
| 供應商設備封裝： | 68-TQFN-EP（10x10） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
If drawn, the simplified dominant highpass network
would look like Figure 3.
The highpass pole in this case is at fP = 1/(2 x pi x RC)
~ 5Hz. Note that this low highpass corner frequency is
required to filter the downconverted clutter tone, which
appears at DC, but not interfere with CWD imaging at
frequencies as low as 400Hz. For example, if one want-
ed to use CWD down to 400Hz, then a good choice for
the highpass pole would be at least a decade below
this (< 40Hz) as not to incur rolloff due to the pole.
Remember, if the highpass pole is set to 400Hz, the
response is 3dB down at that corner frequency. The
placement of the highpass pole at 5Hz in the above
example is between the DC and 40Hz limitations just
discussed.
The bottom line is that any reasonably sized DC block
between the output of the mixer and the instrumentation
amplifier poses a significant time constant that slows
the mode select switching speed.
An alternative solution to the approach in Figure 2,
which enables faster mode select response time, is
shown in Figure 4.
In Figure 4, the outputs of the CWD mixers are DC-cou-
pled into the inputs of the instrumentation amplifiers.
Therefore, the op amps must be able to accommodate
the full compliance range of the mixer outputs, which is
a maximum of 11V when the mixers are disabled, down
to the 5V supply of the MAX2078 when the mixers are
enabled. The op amps can be powered from 11V for the
high rail and 5V for the low rail, requiring a 6V op amp.
Serial Interface
The MAX2078 is programmed using a serial shift regis-
ter arrangement. This greatly simplifies the complexity
of the program circuitry, reduces the number of IC pins
necessary for programming, and reduces the PCB lay-
out complexity. See Table 5 for the programming bit
order. The data in (DIN) and data out (DOUT) can be
daisy-chained from device to device and all front-ends
can run off a single programming clock.
The data can be entered after
CS goes low. Once a
whole word is entered,
CS needs to rise. When pro-
gramming the part, enter LSB first and MSB last.
Programming the Beamformer
During the normal CWD mode, the mixer clock (LO+,
LO-) is on and the programming signals (DIN, CLK,
CS)
are off (
CS = high, CLK = low, and DIN = don’t care, but
fixed to a high or a low). To start the programming
sequence, turn off the mixer clock. Data is shifted into
the shift register at a recommended 10MHz program-
ming rate or 100ns minimum data clock period/time.
Assuming a 64-channel CWD receiver, this takes about
30ms for 5 bits per channel. See Figure 5 for timing
details. After the shift registers are programmed, pulling
CS high loads the internal counters into I/Q phase
divider/selectors with the proper values. The mixer clock
needs to be off when this occurs or there may be timing
issues between the load line timing and the mixer clock
timing. The user turns on the mixer clock to start beam-
forming. The clock must turn on so that it starts at the
beginning of a mixer clock cycle. A narrow glitch on the
mixer clock is not acceptable and could cause metasta-
bility in the I/Q phase dividers.
MAX2078
Octal-Channel Ultrasound Front-End
with CW Doppler Mixers
20
______________________________________________________________________________________
Figure 3. Simplified Circuit of Highpass Pole
+11V
+5V
Figure 4. Improved Mode Select Response Time Achieved with
DC-Coupled Input to Instrumentation Amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3971AUTP+ | IC AMP LIMIT 10.7GBPS 20-TQFN |
| MAX3861ETG+ | IC AMP POST W/AGC 24-TQFN-EP |
| MAX3654ETE+ | IC AMP TRANSIMPEDANCE 16-TQFN |
| LTC2753ACUK-16#TRPBF | IC DAC 16BIT DUAL 48-QFN |
| DAC8800FSZ-REEL | IC DAC 8BIT OCTAL CMOS 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2078CTK+ | 功能描述:射頻前端 8Ch Ultrasound Front-End RoHS:否 制造商:Skyworks Solutions, Inc. 類型: 工作頻率:2.4 GHz, 5 GHz 最大數據速率:54 Mbps 噪聲系數: 工作電源電壓:3.3 V 電源電流:180 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 |
| MAX2078CTK+T | 功能描述:射頻前端 8Ch Ultrasound Front-End RoHS:否 制造商:Skyworks Solutions, Inc. 類型: 工作頻率:2.4 GHz, 5 GHz 最大數據速率:54 Mbps 噪聲系數: 工作電源電壓:3.3 V 電源電流:180 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 |
| MAX2078EVKIT | 功能描述:射頻前端 Ultrasound Integrated Analog Front End Octal LNA RoHS:否 制造商:Skyworks Solutions, Inc. 類型: 工作頻率:2.4 GHz, 5 GHz 最大數據速率:54 Mbps 噪聲系數: 工作電源電壓:3.3 V 電源電流:180 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 |
| MAX2079 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:每個通道具有獨立的混頻器，以優化CWD靈敏度 |
| MAX2079CXE+ | 功能描述:射頻接收器 8Ch Ultrasound Front End w/ADC+CW Doppler RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。