- 您現在的位置：買賣IC網 > PDF目錄9870 > MAX191BEWG+T (Maxim Integrated Products)IC ADC 12BIT 100KSPS 24-SOIC PDF資料下載
參數資料
| 型號： | MAX191BEWG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 100KSPS 24-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 100k |
| 數據接口： | MICROWIRE?，并聯，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 941mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
which can be achieved using power-down between
conversions.
External Compensation
Figure 19a shows the connection for external compensa-
tion with reference adjustment. In this mode, an external
4.7F capacitor compensates the reference output
amplifier, allowing for maximum conversion speed and
lowest conversion noise. However, when reactivating the
ADC after power-down, the reference takes typically 2ms
to fully charge the 4.7F capacitor, so more time is
required before a conversion can start (Figure 19b).
Thus, the average current consumed in power-up/power-
down operations is higher in external compensation
mode than in internal compensation mode.
Gain and Offset Adjustment
Figure 20 depicts the nominal, unipolar input/output (I/O)
transfer function, and Figure 22 shows the bipolar I/O
transfer function. Code transitions occur halfway between
successive integer LSB values. Note that 1LSB = 1.00mV
(4.096V/4096) for unipolar operation and 1LSB = 1.00mV
((4.096V/2 - -4.096V/2)/4096) for bipolar operation.
Figures 19a and 21a show how to adjust the ADC gain
in applications that require full-scale range adjustment.
The connection shown in Figure 21a provides ±0.5%
for ±20LSBs of adjustment range and is recommended
for applications that use an external reference. On the
other hand, Figure 19a is recommended for applica-
tions that use the internal reference, because it uses
fewer external components.
If both offset and full scale need adjustment, the circuit
in Figure 21b is recommended. For single-supply
ADCs, it is virtually impossible to null system negative
offset errors. However, the MAX191 input configuration
is pseudo-differential—only the difference in voltage
between AIN+ and AIN- will be converted into its digital
representation. By applying a small positive voltage to
AIN-, the 0 input voltage at AIN+ can be adjusted to
above or below AIN- voltage, thus nulling positive or
negative system offset errors. R9 and R10 can be
removed for applications that require only positive sys-
tem errors to be nulled. To trim the offset error of the
MAX191, apply 1/2LSB to the analog input and adjust
R6 so the digital output code changes between 000
(hex) and 001 (hex). To adjust full scale, apply FS - 1
1/2LSBs and adjust R2 until the output code changes
MAX191
Low-Power, 12-Bit Sampling ADC
with Internal Reference and Power-Down
______________________________________________________________________________________
19
25
s
RD
0
1
PD
20
s
15
s
VREF
Figure 18b. Low Average-Power Mode Operation (Internal
Compensation)
10,000
10
100
1000
fg18c
CONVERSIONS PER SECOND
SUPPLY
CURRENT
(
A)
50
200
1k
5k
20k
100k
Figure 18c. Average Supply Current vs. Conversion Rate,
Powering Down Between Conversions
MAX191
VREF
REFADJ
PD
1
5
6
0.1
F
4.7
F
5k
11k
15k
100k
0.01
F
Figure 19a. External-Compensation Mode with Internal
Reference Adjustment Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MS3100A28-51S | CONN RCPT 12POS WALL MNT W/SCKT |
| MS27467T17A99S | CONN PLUG 23POS STRAIGHT W/SCKT |
| MS27484T10B99SA | CONN PLUG 7POS STRAIGHT W/SCKT |
| MS3100R28-18P | CONN RCPT 12POS WALL MNT W/PINS |
| MS3126F14-15SZ | CONN PLUG 15POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX191BEWG-W | 制造商:Maxim Integrated Products 功能描述:PLS. RUSH THIS REQUEST, LARRY SCHMIDT/MAT'LS WAITING FOR - Rail/Tube |
| MAX191BMRG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX191BMRG/883B | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX191EVKIT-DIP | 功能描述:數據轉換 IC 開發工具 Evaluation System/Evaluation Kit for the MAX191 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX191EVSYS-DIP | 功能描述:數據轉換 IC 開發工具 Low-Power 12-Bit Sampling ADC with Internal Reference and Power-Down RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。