- 您現在的位置：買賣IC網 > PDF目錄384652 > MAX1617A (Maxim Integrated Products, Inc.) Remote/Local Temperature Sensor with SMBus Serial Interface PDF資料下載
參數資料
| 型號： | MAX1617A |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Remote/Local Temperature Sensor with SMBus Serial Interface |
| 中文描述： | 遠端/本地溫度傳感器，帶有SMBus串行接口 |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 234K |
| 代理商： | MAX1617A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
PC Board Layout
1) Place the MAX1617A as close as practical to the
remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 4 in. to
8 in. (typical) or more as long as the worst noise
sources (such as CRTs, clock generators, memory
buses, and ISA/PCI buses) are avoided.
2) Do not route the DXP–DXN lines next to the deflec-
tion coils of a CRT. Also, do not route the traces
across a fast memory bus, which can easily intro-
duce +30°C error, even with good filtering.
Otherwise, most noise sources are fairly benign.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other, away from any high-
voltage traces such as +12V
DC
. Leakage currents
from PC board contamination must be dealt with
carefully, since a 20M
leakage path from DXP to
ground causes about +1°C error.
4) Connect guard traces to GND on either side of the
DXP–DXN traces (Figure 2). With guard traces in
place, routing near high-voltage traces is no longer
an issue.
5) Route through as few vias and crossunders as possi-
ble to minimize copper/solder thermocouple effects.
6) When introducing a thermocouple, make sure that
both the DXP and the DXN paths have matching
thermocouples. In general, PC board-induced ther-
mocouples are not a serious problem. A copper-sol-
der thermocouple exhibits 3μV/°C, and it takes
about 200μV of voltage error at DXP–DXN to cause
a +1°C measurement error. So, most parasitic ther-
mocouple errors are swamped out.
7) Use wide traces. Narrow ones are more inductive
and tend to pick up radiated noise. The 10 mil
widths and spacings recommended in Figure 2
aren’t absolutely necessary (as they offer only a
minor improvement in leakage and noise), but try to
use them where practical.
8) Keep in mind that copper can’t be used as an EMI
shield, and only ferrous materials, such as steel, work
well. Placing a copper ground plane between the
DXP-DXN traces and traces carrying high-frequency
noise signals does not help reduce EMI.
PC Board Layout Chec klist
Place the MAX1617A close to a remote diode.
Keep traces away from high voltages (+12V bus).
Keep traces away from fast data buses and CRTs.
Use recommended trace widths and spacings.
Place a ground plane under the traces.
Use guard traces flanking DXP and DXN and con-
necting to GND.
Place the noise filter and the 0.1μF V
CC
bypass
capacitors close to the MAX1617A.
Add a 200
resistor in series with V
CC
for best noise
filtering (see Typical Operating Circuit.
T wisted Pair and S hielded Cables
For remote-sensor distances longer than 8 in., or in par-
ticularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6 feet to 12 feet (typical)
before noise becomes a problem, as tested in a noisy
electronics laboratory. For longer distances, the best
solution is a shielded twisted pair like that used for audio
microphones. For example, the Belden 8451 works well
for distances up to 100 feet in a noisy environment.
Connect the twisted pair to DXP and DXN and the shield
to GND, and leave the shield’s remote end unterminated.
Excess capacitance at DX_ limits practical remote sen-
sor distances (see Typical Operating Characteristics).
For very long cable runs, the cable’s parasitic capaci-
tance often provides noise filtering, so the 2200pF
capacitor can often be removed or reduced in value.
Cable resistance also affects remote-sensor accuracy;
1
series resistance introduces about +1/2°C error.
Low-Power S tandby Mode
Standby mode disables the ADC and reduces the sup-
ply-current drain to less than 10μA. Enter standby
mode by forcing the
STBY
pin low or via the RUN/STOP
bit in the configuration byte register. Hardware and
software standby modes behave almost identically: all
data is retained in memory, and the SMB interface is
alive and listening for reads and writes. The only differ-
ence is that in hardware standby mode, the one-shot
command does not initiate a conversion.
Standby mode is not a shutdown mode. With activity on
the SMBus, extra supply current is drawn (see Typical
Operating Characteristics). In software standby mode,
M
Remote/Loc al Temperature S ensor
with S MBus S erial Interfac e
_______________________________________________________________________________________
9
MINIMUM
10 MILS
10 MILS
10 MILS
10 MILS
GND
DXN
DXP
GND
Figure 2. Recommended DXP/DXN PC Traces
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1618 | Remote Temperature Sensor with SMBus Serial Interface |
| MAX1618MUB | Remote Temperature Sensor with SMBus Serial Interface |
| MAX1619MEE | Remote/Local Temperature Sensor with Dual- Alarm Outputs and SMBus Serial Interface |
| MAX1619 | Remote/Local Temperature Sensor with Dual- Alarm Outputs and SMBus Serial Interface |
| MAX1636 | Low-Voltage, Precision Step-Down Controller for Portable CPU Power |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1617AEVKIT | 功能描述:板上安裝溫度傳感器 Evaluation Kit for the MAX1617A RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE+ | 功能描述:板上安裝溫度傳感器 Remote/Local w/SMBus Serial Interface RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE+ | 制造商:Maxim Integrated Products 功能描述:IC TEMP SENSOR 8BIT ?2.5 |
| MAX1617AMEE+T | 功能描述:板上安裝溫度傳感器 Remote/Local w/SMBus Serial Interface RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。