- 您現在的位置：買賣IC網 > PDF目錄384652 > MAX1617A (Maxim Integrated Products, Inc.) Remote/Local Temperature Sensor with SMBus Serial Interface PDF資料下載
參數資料
| 型號： | MAX1617A |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Remote/Local Temperature Sensor with SMBus Serial Interface |
| 中文描述： | 遠端/本地溫度傳感器，帶有SMBus串行接口 |
| 文件頁數： | 10/18頁 |
| 文件大小： | 234K |
| 代理商： | MAX1617A |
the MAX1617A can be forced to perform A/D conver-
sions via the one-shot command, despite the RUN/STOP
bit being high.
Activate hardware standby mode by forcing the
STBY
pin low. In a notebook computer, this line may be con-
nected to the system SUSTAT# suspend-state signal.
The
STBY
pin low state overrides any software conversion
command. If a hardware or software standby command is
received while a conversion is in progress, the conversion
cycle is truncated, and the data from that conversion is not
latched into either temperature reading register. The previ-
ous data is not changed and remains available.
Supply-current drain during the 125ms conversion peri-
od is always about 450μA. Slowing down the conver-
sion rate reduces the average supply current (see
Typical Operating Characteristics). Between conver-
sions, the instantaneous supply current is about 25μA
due to the current consumed by the conversion rate
timer. In standby mode, supply current drops to about
3μA. At very low supply voltages (under the power-on-
reset threshold), the supply current is higher due to the
address pin bias currents. It can be as high as 100μA,
depending on ADD0 and ADD1 settings.
S MBus Digital Interfac e
From a software perspective, the MAX1617A appears as
a set of byte-wide registers that contain temperature
data, alarm threshold values, or control bits. A standard
SMBus 2-wire serial interface is used to read tempera-
ture data and write control bits and alarm threshold data.
Each A/D channel within the device responds to the
same SMBus slave address for normal reads and writes.
The MAX1617A employs four standard SMBus protocols:
Write Byte, Read Byte, Send Byte, and Receive Byte
(Figure 3). The shorter Receive Byte protocol allows
quicker transfers, provided that the correct data register
was previously selected by a Read Byte instruction. Use
caution with the shorter protocols in multi-master systems,
since a second master could overwrite the command
byte without informing the first master.
The temperature data format is 7 bits plus sign in two’s
complement form for each channel, with each data bit rep-
resenting 1°C (Table 2), transmitted MSB first. Measure-
ments are offset by +1/2°C to minimize internal rounding
errors; for example, +99.6°C is reported as +100°C.
M
Remote/Loc al Temperature S ensor
with S MBus S erial Interfac e
10
______________________________________________________________________________________
ACK
7 bits
ADDRESS
ACK
WR
8 bits
DATA
ACK
1
P
8 bits
S
COMMAND
Write Byte Format
Read Byte Format
S end Byte Format
Rec eive Byte Format
Slave Address: equiva-
lent to chip-select line of
a 3-wire interface
Command Byte: selects which
register you are writing to
Data Byte: data goes into the register
set by the command byte (to set
thresholds, configuration masks, and
sampling rate)
ACK
7 bits
ADDRESS
ACK
WR
S
ACK
8 bits
DATA
7 bits
ADDRESS
RD
8 bits
///
P
S
COMMAND
Slave Address: equiva-
lent to chip-select line
Command Byte: selects
which register you are
reading from
Slave Address: repeated
due to change in data-
flow direction
Data Byte: reads from
the register set by the
command byte
ACK
7 bits
ADDRESS
WR
8 bits
COMMAND
ACK
P
S
ACK
7 bits
ADDRESS
RD
8 bits
DATA
///
P
S
Command Byte: sends com-
mand with no data, usually
used for one-shot command
Data Byte: reads data from
the register commanded
by the last Read Byte or
Write Byte transmission;
also used for SMBus Alert
Response return address
S = Start condition
P = Stop condition
Shaded = Slave transmission
/// = Not acknowledged
Figure 3. SMBus Protocols
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1618 | Remote Temperature Sensor with SMBus Serial Interface |
| MAX1618MUB | Remote Temperature Sensor with SMBus Serial Interface |
| MAX1619MEE | Remote/Local Temperature Sensor with Dual- Alarm Outputs and SMBus Serial Interface |
| MAX1619 | Remote/Local Temperature Sensor with Dual- Alarm Outputs and SMBus Serial Interface |
| MAX1636 | Low-Voltage, Precision Step-Down Controller for Portable CPU Power |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1617AEVKIT | 功能描述:板上安裝溫度傳感器 Evaluation Kit for the MAX1617A RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE+ | 功能描述:板上安裝溫度傳感器 Remote/Local w/SMBus Serial Interface RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1617AMEE+ | 制造商:Maxim Integrated Products 功能描述:IC TEMP SENSOR 8BIT ?2.5 |
| MAX1617AMEE+T | 功能描述:板上安裝溫度傳感器 Remote/Local w/SMBus Serial Interface RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。