參數資料
型號： MAX14820ETG+
廠商： Maxim Integrated Products
文件頁數： 20/30頁
文件大?。?/td> 0K
描述： IC IO-LINK TXRX 24TQFN
標準包裝： 75
系列： *
MAX14820
IO-Link Device Transceiver
27
Maxim Integrated
Applications Information
UART Interfacing
The logic levels of the microcontroller interface I/Os
(TXC, TXQ, TXEN, and RX) are defined by VL.
The device can be interfaced to microcontrollers where the
on-board UART TX output cannot be programmed as a logic
output (GPO). In this case, connect the TX output of the UART
to the TXC input for IO-Link communication and connect a
separate GPO output on the microcontroller to TXQ for stan-
dard IO (SIO) mode operation (Figure 12). As the TXQ and
TXC inputs are internally logically ANDed, the unused input
(TXC or TXQ) must be held high while the other is in operation.
Transient Protection
Inductive load switching, surges, and bursts create high
transient voltages. C/Q, DO, and DI should be protect-
ed against high overvoltage and undervoltage transients.
Positive voltage transients on C/Q, DO, and DI must be lim-
ited to +55V relative to GND and negative voltage transients
must be limited to -55V (relative to VCC) on DO and C/Q and
to -55V (relative to GND) on DI. Figure 12 shows suitable
protection using TVS diodes to meet both the IEC 61000-
4-2 ESD and IEC 61000-4-5 surge testing. Other protection
schemes may also be suitable.
The device has to be protected against transients that
occur during hot-plugging of the L+ sensor supply (VCC
input). This is achieved by placing a 10
W resistor with
1F capacitor before LDOIN and connecting an RC
between the sensor supply input and the VCC pin, as
shown in Figure 13. The RC time constant of the filter on
VCC should be larger or equal to 0.8s. In case that VL is
supplied by V5 and the bypass capacitor on V5 is 100nF,
the 10
W resistor in series with LDOIN is not needed.
External Powering
The MAX14820 is powered by VCC and V5. VL is a reference
voltage input to set the logic levels of the microcontroller
interface. The logic and SPI interface are operational when
V5 and VL are present even if VCC is not present.
The VP output provides a reverse-polarity-protected voltage
one diode drop below VCC and can be used for supplying
external circuitry, like power supplies. The current drawn from
VP cannot exceed 50mA. Be aware that capacitance on VP
can cause transient currents at power-up equal to C x dVCC/
dt. In order to reduce power dissipated in the device, an
reverse protection diode can be used to power the external
circuitry, instead of using VP, as shown in Figure 15.
V5 is typically powered by the internal 5V regulator, but
can alternatively be powered by an external 5V regula-
tor. When powering V5 externally, connect LDOIN to V5.
(Figure 15). This configuration disables operation of the
internal 5V regulator and reduces power consumption.
When an external 5V regulator is used to power V5, the
V5 bypass capacitance is determined by that regulator,
and is not limited to 100nF.
Figure 12. UART Interface
Figure 13. MAX14820 Operating Circuit with TVS Protection
MICROCONTROLLER
TXQ
GPO
TXC
TX
TXEN
RTS
RX
MAX14820
0.8
1F
VCC
LDOIN
DO
1/2
SDC36C
1/2
SDC36C
GND
C/Q
1/2
SDC36C
DI
VP
10
相關PDF資料
PDF描述
MAX14821ETG+ IC IO-LINK 24-TQFN
MAX14824GTG+ IC IO-LINK MASTER TXRX 24TQFN
MAX1482CSD-T IC TXRX RS485/422 250KBPS 14SOIC
MAX14830ETM+ SEMICONDUCTOR OTHER
MAX14841EASA+T IC TXRX RS485 40MBPS 8SOIC
相關代理商/技術參數
參數描述
MAX14820ETG+ 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MAX14820ETG+T 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MAX14820EVKIT# 功能描述:界面開發工具 MAX14820/21 EVAL KIT RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
MAX14821ETG+ 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MAX14821ETG+T 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*