- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX14820ETG+ (Maxim Integrated Products)IC IO-LINK TXRX 24TQFN PDF資料下載
參數資料
| 型號： | MAX14820ETG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC IO-LINK TXRX 24TQFN |
| 標準包裝： | 75 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX14820
IO-Link Device Transceiver
21
Maxim Integrated
CQConfig Register [R1, R0] = [0,1]
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Bit Name
RxFilter
HiSlew
C/Q_N/P
C/Q_PP
C/QDEn
Q
RxDis
C/QLoad
Read/Write
R/W
POR State
0
Use the CQConfig register to control the C/Q receiver and driver parameters. All bits in the CQConfig register are
read-write and are set to 0 at power-up.
BIT
NAME
DESCRIPTION
D7
RxFilter
C/Q and DI Receiver Filter Control. The C/Q and DI receivers have analog
lowpass filters to reduce high-frequency noise on the receiver inputs. Set the
RxFilter bit to 0 to set the filter corner frequency to 500kHz. Set the RxFilter
bit to 1 to set the filter corner frequency to 1MHz (this setting is used for high-
speed COM3 operation).
Noise filters on C/Q and DI are controlled simultaneously by the RxFilter bit.
D6
HiSlew
Slew-Rate Control. The HiSlew bit increases the slew rate for the C/Q and
DO drivers and is used for high-speed COM3 (230kbps) data rates. Set
HiSlew to 0 for COM1 and COM2 operation.
D5
C/Q_N/P
C/Q Driver NPN/PNP Mode. The C/Q_N/P bit selects between low-side (NPN)
and high-side (PNP) modes when the C/Q driver is configured as an open-
drain output (C/Q_PP = 0). Set C/Q_N/P to 1 to configure the driver for low-side
(NPN) operation. Set C/Q_N/P to 0 for high-side (PNP) operation.
D4
C/Q_PP
C/Q Driver Push-Pull Operation. Set C/Q_PP to 1 to enable push-pull
operation on the C/Q driver. The C/Q output is open-drain when C/Q_PP is 0.
D3
C/QDEn
C/Q Driver Enable/Disable. Set the C/QDEn bit to 1 to enable the C/Q driver.
Set C/QDEn to 0 for hardware (TXEN) control. See Table 4.
D2
Q
C/Q Driver Output Logic. The Q bit can be used to program the C/Q output
driver through software. The C/Q driver must be enabled and TXC = TXQ must
be high to control the C/Q driver through the Q bit (Figure 8). C/Q has the
same logic polarity as the Q bit.
Set the Q bit to 0 to control the C/Q driver with TXC and TXQ.
The C/Q driver output state depends on the C/Q_PP and C/Q_N/P bits as
shown in Table 5. Note that Table 5 assumes that the C/Q driver is enabled
(TXEN = VL or C/QDEn = 1).
D1
RxDis
C/Q Receiver Enable/Disable. Set the RxDis bit to 1 to disable the C/Q
receiver. The RX output is high when RxDis is 1.
D0
C/QLoad
C/Q Current Sink Enable. Set the C/QLoad bit to 1 to enable the internal
current sink at C/Q.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14821ETG+ | IC IO-LINK 24-TQFN |
| MAX14824GTG+ | IC IO-LINK MASTER TXRX 24TQFN |
| MAX1482CSD-T | IC TXRX RS485/422 250KBPS 14SOIC |
| MAX14830ETM+ | SEMICONDUCTOR OTHER |
| MAX14841EASA+T | IC TXRX RS485 40MBPS 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14820ETG+ | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14820ETG+T | 功能描述:輸入/輸出控制器接口集成電路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14820EVKIT# | 功能描述:界面開發工具 MAX14820/21 EVAL KIT RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX14821ETG+ | 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MAX14821ETG+T | 功能描述:輸入/輸出控制器接口集成電路 NEW RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。