參數資料
型號： MAX1464AAI+T
廠商： Maxim Integrated Products
文件頁數： 10/47頁
文件大?。?/td> 0K
描述： IC SENSOR SIGNAL COND 28-SSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,000
類型： 信號調節器
輸入類型： 模擬
輸出類型： 邏輯
接口： SPI
電流 - 電源： 890µA
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 28-SSOP
包裝： 帶卷 (TR)
MAX1464
Low-Power, Low-Noise Multichannel
Sensor Signal Processor
18
Maxim Integrated
Every function of the DOP module can be selected individ-
ually (DAC, PWM, or op amp), or two out of the three func-
tions of the DOP module can be selected at the same time
(PWM and op amp, or DAC and PWM, or DAC and op
amp), as there are only two output pins for the module,
OUTnSM and OUTnLG. The various configuration options
for the DOP are shown in Table 21. The PWRDAC and
PWROP bits are in the power-on control register (address
= 31h), and the remaining bits are in the DOP registers.
See Tables 21 through 27.
Timer Module
The timer module (Figure 6) comprises a 12-bit counter, a
4-bit prescalar, and control and configuration registers.
When the timer is enabled and initiated, the system master
clock, MCLK, is prescaled by the divisor set by PS[3:0] in
the TMR_Config register and the result applied to the 12-
bit upcounter. When the counter value matches the time-
out value TO[11:0] in register TMR_Config, bit TMDN is set
to 1. The CPU can poll the timer done bit TMDN to check
its status.
The timer module provides a feature that enables the CPU
to be put into a low-power halt mode for the duration of the
timer interval. Setting the ENAHALT bit in the TMR_Control
register while starting the timer (setting the timer enable bit
TMEN to 1), or while the timer is already enabled and
counting halts the CPU at the present instruction until the
TMDN bit becomes set by the counter. The CPU com-
mences execution with the next instruction. All CPU regis-
ters and ports are fully static and retain all data during the
elapsed time interval.
The time interval between TMEN being set to 1, and
TMDN being set to 1 can be computed as follows:
Time Interval = (2 / fOSC) x {(prescale value N)
x (timeout value TO[11:0]) + 1.5}
The maximum time interval given fOSC = 4MHz clock is
786ms.
Power Control
The power to various subcircuits in the MAX1464 can be
turned on and off by CPU control and by the serial inter-
face. Unused subcircuits and modules can be turned off
to reduce power consumption. The default state after
power-on is all subcircuits and modules powered off.
This enables low-power embedded systems to turn on
only the needed modules after exiting a low-power CPU
halt timer interval. Modules can be turned on and off as
needed; however, care must be exercised to allow for
module initialization and settling prior to use.
Oscillator Control
The MAX1464 has a fully integrated oscillator with a
nominal 4MHz frequency. An external clock source can
be used when the clock-select pin CKSEL = 0, operating
all internal timing functions. CKIO can also be configured
as an output source of the internal oscillator clock.
GPIO Module
The MAX1464 contains two general-purpose digital
input/output (GPIO) modules, GPIO1 and GPIO2, which
can be written and read by CPU control and by the ser-
ial interface. These two I/O pins operate independently
of each other. They can be configured as inputs, out-
puts, or one input and one output. When configured as
an input, there are two modes of sensing digital inputs;
as a voltage or logic level, or as an edge detector. In
edge-detector mode, either a rising or falling edge can
be selected for detection. A bit is set in the GPIO con-
trol register upon detection of the selected edge.
The GPIO pins have nominal 100k
Ω pulldown resistors
to VSS as in Figure 6. Pulldown resistors provide a low
logic level when the pin is unconnected. The GPIO may
also serve as an input pin and its state is read from the
GPIO control register (Tables 28 and 29). When using
the GPIO pin as a general-purpose output, its output
state is defined by writing to the GPIO control register.
The GPIOn pins can be configured as an alert output
that goes low or high whenever a fault condition hap-
pens, e.g., remote sensor line disconnection, overflow
conditions in the CPU program execution, etc.
All input and output control for the GPIO1 and GPIO2
pins are contained in GPIO1_Control (address = 40h)
and GPIO2_Control (address = 41h), respectively.
Figure 7 shows the GPIO1 and GPIO2 modules.
Serial Interface Timing and Operation
The MAX1464 serial interface is a high-speed asyn-
chronous data input and output communication port,
providing access to internal registers for calibration of
embedded control sensor systems. All the FLASH
memory is read and write accessible by the serial inter-
20h
TMR_Control
21h
TMR_Config
PRESCALER
12-BIT COUNTER
TIMEOUT VALUE
MCLK
Figure 6. Timer Module
相關PDF資料
PDF描述
MAX1474AXT+T IC ELECTRONIC CAPACITOR SC70-6
MAX14753EUE+T IC MULTIPLEXER DUAL 4X1 16TSSOP
MAX14756EUE+T IC ANLG SWITCH SPST QUAD 16TSSOP
MAX14759ETA+ IC SWITCH ANALOG 8-TDFN-EP
MAX14764ETA+T IC ANALOG SWITCH
相關代理商/技術參數
參數描述
MAX1464CAI 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI+ 功能描述:數字信號處理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI+T 功能描述:數字信號處理器和控制器 - DSP, DSC Low-Power Low-Noise Multichannel Sensor Signal Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464CAI-T 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MAX1464EAI 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*