參數資料
型號： MAX1403EVKIT
廠商： Maxim Integrated Products
文件頁數： 24/36頁
文件大?。?/td> 0K
描述： EVAL KIT FOR MAX1403
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
ADC 的數量： 1
位數： 18
采樣率（每秒）： 480
數據接口： 串行
輸入范圍： ±VREF/增益
在以下條件下的電源（標準）： 16.9mW @ 480SPS
工作溫度： 0°C ~ 70°C
已用 IC / 零件： MAX1403
已供物品： 板，CD
Analog Filtering
The digital filter does not provide any rejection close to
the harmonics of the modulator sample frequency.
However, due to the high oversampling ratio of the
MAX1403, these bands occupy only a small fraction of
the spectrum and most broadband noise is filtered.
Therefore, the analog filtering requirements in front of
the MAX1403 are considerably reduced compared to a
conventional converter with no on-chip filtering. In addi-
tion, because the part’s common-mode rejection of
90dB extends out to several kHz, common-mode noise
susceptibility in this frequency range is substantially
reduced.
Depending on the application, it may be necessary to
provide filtering prior to the MAX1403 to eliminate
unwanted frequencies the digital filter does not reject. It
may also be necessary in some applications to provide
additional filtering to ensure that differential noise sig-
nals outside the frequency band of interest do not satu-
rate the analog modulator.
If passive components are placed in front of the
MAX1403, when the part is used in unbuffered mode,
ensure that the source impedance is low enough not to
introduce gain errors in the system (Tables 13a–13d).
This can significantly limit the amount of passive anti-
aliasing filtering that can be applied in front of the
MAX1403 in unbuffered mode. However, when the part
is used in buffered mode, large source impedances will
simply result in a small DC offset error (a 1k
source
resistance will cause an offset error of less than 10V).
Therefore, where any significant source impedances
are required, Maxim recommends operating the part in
buffered mode.
Calibration Channels
Two fully differential calibration channels allow mea-
surement of the system gain and offset errors. Connect
the CALOFF channel to 0V and the CALGAIN channel
to the reference voltage. Average several measure-
ments on both CALOFF and CALGAIN. Subtract the
average offset code and scale to correct for the gain
error. This linear calibration technique can be used to
remove errors due to source impedances on the analog
input (e.g., when using a simple RC anti-aliasing filter
on the front end).
Applications Information
SPI Interface (68HC11, PIC16C73)
Microprocessors with a hardware SPI (serial peripheral
interface) can use a 3-wire interface to the MAX1403
(Figure 12). The SPI hardware generates groups of
eight pulses on SCLK, shifting data in on one pin and
out on the other pin.
For best results, use a hardware interrupt to monitor the
INT pin and acquire new data as soon as it is available.
If hardware interrupts are not available, or if interrupt
latency is longer than the selected conversion rate, use
the FSYNC bit to prevent automatic measurement while
reading the data output register.
The example code in Listing 1 shows how to interface
with the MAX1403 using a 68HC11. System-dependent
initialization code is not shown.
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
30
______________________________________________________________________________________
VDD
SS
INTERRUPT
SCK
MISO
MOSI
RESET
INT
SCLK
DOUT
DIN
CS
VDD
68HC11
MAX1403
Figure 12. MAX1403 to 68HC11 Interface
-160
-140
-100
-120
-80
-60
-20
-40
0
406080
20
100 120 140 160 180 200
FREQUENCY (Hz)
GAIN
(dB)
fCLKIN = 2.4576MHz
MF1, 0 = 0
FS1, 0 = 0
fN = 50Hz
Figure 11. Frequency Response of the SINC3 Filter
(Notch at 50Hz)
相關PDF資料
PDF描述
GEC36DRES-S13 CONN EDGECARD 72POS .100 EXTEND
VI-2W4-EY CONVERTER MOD DC/DC 48V 50W
380LX121M400J022 CAP ALUM 120UF 400V 20% SNAP
SDR7045-470K INDUCTOR POWER 47UH 10% SMD
AC1059 SOCKET FOR MODEL AD210 IC
相關代理商/技術參數
參數描述
MAX1403EVL11 功能描述:數據轉換 IC 開發工具 MAX1403 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1403EVSYSTEM 制造商:Maxim Integrated Products 功能描述:EVALUATION SYSTEM FOR THE MAX1403 - Boxed Product (Development Kits)
MAX1406C/D 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
MAX1406CAE+ 功能描述:RS-232接口集成電路 15kV ESD-Protected 230kbps RS-232 LD/Rc RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*