參數資料
型號: MAX13174ECAG+
廠商: Maxim Integrated Products
文件頁數: 9/13頁
文件大?。?/td> 0K
描述: IC CBL TERMINATION NETWRK 24SSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 58
類型: 纜線
端子數: 6
電源電壓: 4.5 V ~ 5.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 24-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 24-SSOP
包裝: 管件
MAX13174E
+5V Multiprotocol, Pin-Selectable
Cable Terminator
_______________________________________________________________________________________
5
Detailed Description
The MAX13174E contains six pin-selectable multiproto-
col cable termination networks (Figure 3). Each network
is capable of terminating V.11 (RS-422, RS-530,
RS-530A, RS-449, V.36, and X.21) with a 100
Ω differen-
tial load, V.35 with a T-network load, or V.28 (RS-232)
and V.10 (RS-423) with an open-circuit load for use with
transceivers that have on-chip termination. The termina-
tion protocol can be selected by the serial interface
cable wiring or by pin control. The MAX13174E
replaces discrete resistor termination networks and
expensive relays required for multiprotocol termination,
saving space and cost.
The MAX13174E terminator is designed to form a com-
plete +5V cable- or pin-selectable multiprotocol DCE/DTE
interface port when used with the MAX13170E and
MAX13172E transceivers. The MAX13174E terminator
can use the VEE power generated by the MAX13170E
charge pump, simplifying system design. The
MAX13174E/MAX13170E/MAX13172E are functionally
compatible with the MXL1344A/MXL1543/MXL1544/
MAX3175.
Termination Modes
The termination networks in the MAX13174E can be set
to one of three modes: V.11, V.35, or high impedance.
As shown in Figure 4, in V.11 mode, switch S1 is closed
and switch S2 is open, presenting 104
Ω across termi-
nals A and B. In V.35 mode, switches S1 and S2 are
both closed, presenting a T-network with 104
Ω differen-
tial impedance and 153
Ω common-mode impedance.
In high-impedance mode, switches S1 and S2 are both
open, presenting a high impedance across terminals A
and B suitable for V.28 and V.10 modes.
PIN
NAME
FUNCTION
1
M0
Mode-Select Input (Table 1)
2VEE
Negative Supply Voltage (typically connected to VEE of MAX13170E). Bypass to GND with a 0.1F capacitor.
3
R1C
Load 1, Center Tap
4
R1B
Load 1, Node B
5
R1A
Load 1, Node A
6
R2A
Load 2, Node A
7
R2B
Load 2, Node B
8
R2C
Load 2, Center Tap
9
R3A
Load 3, Node A
10
R3B
Load 3, Node B
11
R3C
Load 3, Center Tap
12, 13
GND
Ground
14
VCC
+5V Supply Voltage. Bypass to GND with a 0.1F capacitor.
15
R4B
Load 4, Node B
16
R4A
Load 4, Node A
17
R5B
Load 5, Node B
18
R5A
Load 5, Node A
19
R6A
Load 6, Node A
20
R6B
Load 6, Node B
21
LATCH
Latch Signal Input. When LATCH is low, the input latches are transparent. When LATCH is high, the data
at the mode-select inputs are latched.
22
DCE/DTE
DCE/DTE Mode-Select Input (Table 1)
23
M2
Mode-Select Input (Table 1)
24
M1
Mode-Select Input (Table 1)
Pin Description
相關PDF資料
PDF描述
MAX13184EESD+ IC TXRX RS-485 +5.0V ESD 14SOIC
MAX13223EEUP+T IC TXRX RS-232 2TX/2RX 20-TSSOP
MAX13234EAUP+ TXRX RS-232 250KBPS 2X2 20TSSOP
MAX1329BETL+ IC DAS 12BIT 300KSPS 40-TQFN-EP
MAX13342EEBC+T IC TXRX USB FS 3WIRE 12-UCSP
相關代理商/技術參數
參數描述
MAX13174ECAG+ 功能描述:接口 - 專用 Pmic Fo Samsung Ap Proc C110/C111 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX13174ECAG+T 功能描述:接口 - 專用 +5V Multiprotocol, P In-Selectable Cable RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX13174EEAG+ 制造商:Maxim Integrated Products 功能描述:+5V MULTIPROTOCOL PIN-SELECTABLE CABLE TERMINATOR - Rail/Tube
MAX13175EETU+ 制造商:Maxim Integrated Products 功能描述:MULTIPROTOCOL PIN-SELECTABLE DATA INTERFACE CHIPSET - Rail/Tube
MAX13175EETU+T 制造商:Maxim Integrated Products 功能描述: