- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX13174ECAG+ (Maxim Integrated Products)IC CBL TERMINATION NETWRK 24SSOP PDF資料下載
參數資料
| 型號： | MAX13174ECAG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/13頁 |
| 文件大小： | 0K |
| 描述： | IC CBL TERMINATION NETWRK 24SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 58 |
| 類型： | 纜線 |
| 端子數： | 6 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 管件 |
MAX13174E
+5V Multiprotocol, Pin-Selectable
Cable Terminator
_______________________________________________________________________________________
9
In Figure 7, the MAX13174E is used to terminate the
V.11 receiver on the MAX13170E. Internal to the
MAX13174E, S1 is closed and S2 is open to present a
104
Ω typical differential resistance and high-Z com-
mon-mode impedance. The MAX13170E's internal V.28
termination is disabled by opening S3.
The V.11 specification allows for signals with common-
mode variations of ±7V and differential signal ampli-
tudes from 2V to 6V. The MAX13174E maintains
termination impedance between 100
Ω and 110Ω over
these conditions.
V.35 Termination
Figure 8 shows a standard V.35 interface. The generator
and the load must both present a 100
Ω ±10Ω differential
impedance and a 150
Ω ±15Ω common-mode imped-
ance. The V.35 driver generates a current output
(±11mA, typ) that develops an output voltage between
440mV and 660mV across the load termination networks.
In Figure 9, the MAX13174E is used to implement the
resistive T-network that is needed to properly terminate
the V.35 receiver. Internal to the MAX13174E, S1 and S2
are closed to connect the T-network resistors to the circuit.
The V.35 specification allows for ±4V of ground difference
between the V.35 generator and V.35 load. The
MAX13174E maintains correct termination impedance
over these conditions.
V.35 EMI reduction
For applications where EMI reduction is especially
important, the MAX13174E termination networks provide
a pin for shunting common-mode driver currents to
GND. Mismatches between the driver A and B output
propagation delays can create a common-mode distur-
bance on the cable. This common-mode energy can be
shunted to GND by placing a 100pF capacitor to GND
from the center tap of the T-network termination (R1C,
R2C, and R3C as shown in Figure 5).
V.28 Termination
Most industry-standard V.28 receivers (including the
MAX13170E and MAX13172E) do not require external
termination because the receiver includes an internal
5k
Ω termination resistor. When the MAX13174E is
100
Ω
MIN
A
′
B
′
C
′
A
B
C
GENERATOR
BALANCED
INTERCONNECTING
CABLE
TERMINATION
RECEIVER
LOAD
Figure 6. Typical V.11 Interface
R6
11k
Ω
R8
5k
Ω
R3
124
Ω
R2
52
Ω
R1
52
Ω
A
′
B
′
C
′
A
B
GND
R5
55k
Ω
1.4V
R7
11k
Ω
R4
55k
Ω
MAX13174E
MAX13170E
S3
S1
RECEIVER
S2
+
-
S1
Figure 7. V.11 Termination and Internal Resistance Networks
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13184EESD+ | IC TXRX RS-485 +5.0V ESD 14SOIC |
| MAX13223EEUP+T | IC TXRX RS-232 2TX/2RX 20-TSSOP |
| MAX13234EAUP+ | TXRX RS-232 250KBPS 2X2 20TSSOP |
| MAX1329BETL+ | IC DAS 12BIT 300KSPS 40-TQFN-EP |
| MAX13342EEBC+T | IC TXRX USB FS 3WIRE 12-UCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13174ECAG+ | 功能描述:接口 - 專用 Pmic Fo Samsung Ap Proc C110/C111 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13174ECAG+T | 功能描述:接口 - 專用 +5V Multiprotocol, P In-Selectable Cable RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13174EEAG+ | 制造商:Maxim Integrated Products 功能描述:+5V MULTIPROTOCOL PIN-SELECTABLE CABLE TERMINATOR - Rail/Tube |
| MAX13175EETU+ | 制造商:Maxim Integrated Products 功能描述:MULTIPROTOCOL PIN-SELECTABLE DATA INTERFACE CHIPSET - Rail/Tube |
| MAX13175EETU+T | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。