when battery voltage is first applied to VBAT. When the
參數資料
型號： MAX13041ASD/V+
廠商： Maxim Integrated Products
文件頁數： 6/20頁
文件大?。?/td> 0K
描述： IC CAN TXRX +/-80V HS 14SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 收發器
驅動器/接收器數： 1/1
規程： CAN
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 管件
MAX13041
when battery voltage is first applied to VBAT. When the
PWON flag is set, UVNOM is cleared and sleep mode is
disabled. The primary function of the PWON flag is to pre-
vent the MAX13041 from entering sleep mode (and there-
by disabling external voltage regulators) before the
protocol controller establishes control through EN and
STB. The PWON flag is externally indicated as a logic-low
on
ERR when the MAX13041 is placed into PWON/listen-
only mode from standby mode, go-to-sleep command
mode, or sleep mode. The PWON flag is cleared when
the MAX13041 enters normal mode.
Wake-Up Flag
The wake-up flag is set when a local or remote wake-up
request is detected. A local wake-up request is gener-
ated when the logic level on WAKE changes and
remains stable for tWAKE. A remote wake-on CAN
request is generated upon the detection of two domi-
nant bus cycles, each followed by a recessive bus
cycle (see Figure 5.) Each bus cycle must exceed
tBUS(DOM). The wake-up flag can only be set in stand-
by mode, go-to-sleep command mode, or sleep mode.
Setting the wake-up flag resets UVNOM, and wake-up
requests are not detected during the UVNOM flag wait-
ing time immediately after UVNOM has been set. The
wake-up flag is immediately available as a logic-low on
ERR and RXD, provided that VI/O and VCC are both
present. The wake-up flag is cleared when the
MAX13041 enters normal mode.
Wake-Up Source Flag
The wake-up source flag is set concurrently with the
wake-up source flag when a local wake-up event is
detected. The wake-up source flag can only be set
after the PWON flag has been cleared. The flag is
cleared when the MAX13041 leaves normal mode and
during initial power-on. The wake-up source flag is
externally indicated on
ERR when the MAX13041 is in
±80V Fault-Protected High-Speed CAN Transceiver
with Low-Power Management and Wake-On CAN
14
______________________________________________________________________________________
CANH
CANL
DOMINANT
RECESSIVE
DOMINANT
RECESSIVE
tBUSDOM
Figure 5. Wake-On-CAN Timing
INTERNAL FLAG
FLAG AVAILABLE ON
ERR
CONDITIONS TO CLEAR FLAG
UVNOM
No
Set PWON or wake-up flags
UVBAT
No
Recovery of VBAT
PWON
In PWON/listen-only mode (changing from
standby, go-to-sleep command, or sleep modes)
Entering normal mode
Wake-Up
In standby, go-to-sleep command, and sleep
modes (provided VI/O and VCC are present)
Entering normal mode or setting PWON or UVNOM
flag
Wake-Up Source
In normal mode (before the fourth dominant to
recessive edge on TXD, Note 10)
Leaving normal mode or setting PWON flag
Bus Failure
In normal mode (after the fourth dominant to
recessive edge on TXD, Note 10)
Re-entering normal mode
Local Failure
In PWON/listen-only mode (coming from normal
mode)
Entering normal mode or whenever RXD is
dominant while TXD is recessive (and all local
failures are resolved)
Table 2. Flag Signaling on
ERR
Note 10: Allow for a dominant time of at least 4s per dominant-recessive cycle.
相關PDF資料
PDF描述
VI-25K-MX-F3 CONVERTER MOD DC/DC 40V 75W
MS27468T17B6P CONN RCPT 6POS JAM NUT W/PINS
78Q2133R/F TXRX 10/100 MDIX 3.3V IND 32-QFN
MAX3314ECKA+T IC TXRX RS232 460KBPS SOT23-8
VI-25K-MX-F1 CONVERTER MOD DC/DC 40V 75W
相關代理商/技術參數
參數描述
MAX13042EEBC+ 制造商:Maxim Integrated Products 功能描述:
MAX13042EEBC+T 功能描述:轉換 - 電壓電平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8
MAX13042EETD+ 制造商:Maxim Integrated Products 功能描述:1.62V TO 3.6V IMPROVED HIGH-SPEED L - Rail/Tube
MAX13042EETD+T 功能描述:轉換 - 電壓電平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8
MAX13042EEVKIT+ 功能描述:電源管理IC開發工具 MAX13042E Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*